- 您現在的位置：買賣IC網 > PDF目錄98165 > TAS5707PHPR (TEXAS INSTRUMENTS INC) 20.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48 PDF資料下載
參數資料
| 型號： | TAS5707PHPR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 20.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48 |
| 封裝： | 7 X 7 MM, GREEN, PLASTIC, HTQFP-48 |
| 文件頁數： | 10/57頁 |
| 文件大?。?/td> | 1000K |
| 代理商： | TAS5707PHPR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
SLOS556B – NOVEMBER 2008 – REVISED NOVEMBER 2009
www.ti.com
Overtemperature Protection
The TAS5707 has a two-level temperature-protection system that asserts an active-high warning signal (OTW)
when the device junction temperature exceeds 125°C (nominal) and, if the device junction temperature exceeds
150°C (nominal), the device is put into thermal shutdown, resulting in all half-bridge outputs being set in the
high-impedance (Hi-Z) state and FAULT being asserted low. The TAS5707 recovers from shutdown
automatically once the temperature drops approximately 30°C. The overtemperature warning (OTW) is disabled
once the temperature drops approximately 25°C.
Undervoltage Protection (UVP) and Power-On
Reset (POR)
The UVP and POR circuits of the TAS5707 fully protect the device in any power-up/down and brownout situation.
While powering up, the POR circuit resets the overload circuit (OLP) and ensures that all circuits are fully
operational when the PVDD and AVDD supply voltages reach 7.6 V and 2.7 V, respectively. Although PVDD and
AVDD are independently monitored, a supply voltage drop below the UVP threshold on AVDD or either PVDD
pin results in all half-bridge outputs immediately being set in the high-impedance (Hi-Z) state and FAULT being
asserted low.
SSTIMER FUNCTIONALITY
The SSTIMER pin uses a capacitor connected between this pin and ground to control the output duty cycle when
exiting all-channel shutdown. The capacitor on the SSTIMER pin is slowly charged through an internal current
source, and the charge time determines the rate at which the output transitions from a near zero duty cycle to the
desired duty cycle. This allows for a smooth transition that minimizes audible pops and clicks. When the part is
shutdown the drivers are tristated and transition slowly down through a 3K resistor, similarly minimizing pops and
clicks. The shutdown transition time is independent of SSTIMER pin capacitance. Larger capacitors will increase
the start-up time, while capacitors smaller than 2.2 nF will decrease the start-up time. The SSTIMER pin should
be left floating for BD modulation.
CLOCK, AUTO DETECTION, AND PLL
The TAS5707 is a slave device. It accepts MCLK, SCLK, and LRCLK. The digital audio processor (DAP)
supports all the sample rates and MCLK rates that are defined in the clock control register .
The TAS5707 checks to verify that SCLK is a specific value of 32 fS, 48 fS, or 64 fS. The DAP only supports a 1 ×
fS LRCLK. The timing relationship of these clocks to SDIN is shown in subsequent sections. The clock section
uses MCLK or the internal oscillator clock (when MCLK is unstable, out of range, or absent) to produce the
internal clock (DCLK) running at 512 time the PWM switching frequency.
The DAP can autodetect and set the internal clock control logic to the appropriate settings for all supported clock
rates as defined in the clock control register.
TAS5707 has robust clock error handling that uses the bulit-in trimmed oscillator clock to quickly detect
changes/errors. Once the system detects a clock change/error, it will mute the audio (through a single step mute)
and then force PLL to limp using the internal oscillator as a reference clock. Once the clocks are stable, the
system will auto detect the new rate and revert to normal operation. During this process, the default volume will
be restored in a single step (also called hard unmute). The ramp process can be programmed to ramp back
slowly (also called soft unmute) as defined in volume register (0X0E).
SERIAL DATA INTERFACE
Serial data is input on SDIN. The PWM outputs are derived from SDIN. The TAS5707 DAP accepts serial data in
16-, 20-, or 24-bit left-justified, right-justified, and I2S serial data formats.
PWM Section
The TAS5707 DAP device uses noise-shaping and sophisticated non-linear correction algorithms to achieve high
power efficiency and high-performance digital audio reproduction. The DAP uses a fourth-order noise shaper to
increase dynamic range and SNR in the audio band. The PWM section accepts 24-bit PCM data from the DAP
and outputs two BTL PWM audio output channels.
18
Copyright 2008–2009, Texas Instruments Incorporated
相關PDF資料 |
PDF描述 |
|---|---|
| TAS5707PHP | 20.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48 |
| TAS5708PHP | 20.2 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48 |
| TAS5708PHPR | 20.2 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48 |
| TAS5709AGPHPR | 20.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48 |
| TAS5709AGPHP | 20.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TAS5708 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:20-W STEREO DIGITAL AUDIO POWER AMPLIFIER WITH EQ/DRC and FEEDBACK |
| TAS5708EVM | 功能描述:音頻 IC 開發工具 TAS5708EVM Eval Mod RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| TAS5708PHP | 功能描述:音頻放大器 20W St Closed-Loop I2S In Aud Pwr Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TAS5708PHPR | 功能描述:音頻放大器 20W St Closed-Loop I2S In Aud Pwr Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TAS5709 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:20-W STEREO DIGITAL AUDIO POWER AMPLIFIER WITH EQ AND DRC |
發布緊急采購，3分鐘左右您將得到回復。