參數資料
型號： TAS5112ADCAR
廠商： Texas Instruments, Inc.
英文描述： DIGITAL AMPLIFIER POWER STAGE
中文描述： 數字放大器功率級
文件頁數： 11/21頁
文件大?。?/td> 405K
代理商： TAS5112ADCAR
SLES094A - OCTOBER 2003 - REVISED MARCH 2004
www.ti.com
11
THEORY OF OPERATION
POWER SUPPLIES
The power device only requires two supply voltages,
GVDD and PVDD_X.
GVDD is the gate drive supply for the device, regulated
internally down to approximately 12 V, and decoupled with
regards to board GND on the GREG pins through an
external capacitor. GREG powers both the low side and
high side via a bootstrap step-up conversion. The
bootstrap supply is charged after the first low-side turn-on
pulse. Internal digital core voltage DREG is also derived
from GVDD and regulated down by internal circuitry to
3.3 V.
The gate-driver regulator can be bypassed for reducing
idle loss in the device by shorting GREG to GVDD and
directly feeding in 12.0 V. This can be useful in an
application where thermal conduction of heat from the
device is difficult.
PVDD_X is the H-bridge power supply pin. Two power pins
exists for each half-bridge to handle the current density. It
is important that the circuitry recommendations around the
PVDD_X pins are followed carefully both topology- and
layout-wise. For topology recommendations, see the
System Configuration Used for Characterization
section.
Following these recommendations is important for
parameters like EMI, reliability, and performance.
POWERING UP
RESET
GVDD
PVDD_X
PWM_xP
> 1 ms
> 1 ms
NOTE:PVDD should not be powered up before GVDD.
During power up when RESET is asserted LOW, all
MOSFETs are turned off and the two internal half-bridges
are in the high-impedance state (Hi-Z). The bootstrap
capacitors supplying high-side gate drive are not charged
at this point. To comply with the click and pop scheme and
use of non-TI modulators, it is recommended to use a
4.7-k
pulldown resistor on each PWM output node to
ground. This precharges the bootstrap supply capacitors
and discharges the output filter capacitor
.
After GVDD has been applied, it takes approximately 800
μ
s to fully charge the BST capacitor. Within this time,
RESET must be kept low. After approximately 1 ms, the
back-end bootstrap capacitor is charged.
RESET can now be released if the modulator is powered
up and streaming valid PWM signals to the back-end
PWM_xP. Valid means a switching PWM signal which
complies with the frequency and duty cycle ranges stated
in the
Recommended Operating Conditions
.
A constant HIGH dc level on the PWM_xP is not permitted,
because it would force the high-side MOSFET ON until it
eventually ran out of BST capacitor energy and might
damage the device.
An unknown state of the PWM output signals from the
modulator is illegal and should be avoided, which in
practice means that the PWM processor must be powered
up and initialized before RESET is de-asserted HIGH to
the back end.
POWERING DOWN
For power down of the back end, an opposite approach is
necessary. The RESET must be asserted LOW before the
valid PWM signal is removed.
When PWM processors are used with TI PurePath Digital
amplifiers, the correct timing control of RESET and
PWM_xP is performed by the modulator.
PRECAUTION
The TAS5112A must always start up in the
high-impedance (Hi-Z) state. In this state, the bootstrap
(BST) capacitor is precharged by a resistor on each PWM
output node to ground. See the system configuration. This
ensures that the back end is ready for receiving PWM
pulses, indicating either HIGH- or LOW-side turnon after
RESET is de-asserted to the back end.
With the following pulldown resistor and BST capacitor
size, the charge time is:
C = 33 nF, R = 4.7
k
R
×
C
×
5 = 775.5
μ
s
After GVDD has been applied, it takes approximately 800
μ
s to fully charge the BST capacitor. During this time,
RESET must be kept low. After approximately 1 ms the
back end BST is charged and ready. RESET can now be
released if the PWM modulator is ready and is streaming
valid PWM signals to the back end. Valid PWM signals are
switching PWM signals with a frequency between 350-400
kHz. A constant HIGH level on the PWM+ would force the
high-side MOSFET ON until it eventually ran out of BST
capacitor energy. Putting the device in this condition
should be avoided.
相關PDF資料
PDF描述
TAS5112ADCARG4 DIGITAL AMPLIFIER POWER STAGE
TAS5121A DIGITAL AMPLIFIER POWER STAGE
TAS5146DKD STEREO DIGITAL AMPLIFIER POWER STAGE
TB0640L 30A BI-DIRECTIONAL SURFACE MOUNT THYRISTOR SURGE PROTECTIVE DEVICE
TB1300L 30A BI-DIRECTIONAL SURFACE MOUNT THYRISTOR SURGE PROTECTIVE DEVICE
相關代理商/技術參數
參數描述
TAS5112ADCARG4 功能描述:音頻放大器 Digital Amp Power Stage RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TAS5112ADFD 功能描述:音頻放大器 Digital Amp Power Stage RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TAS5112ADFDG4 功能描述:音頻放大器 Digital Amp Power Stage RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TAS5112ADFDR 功能描述:音頻放大器 Digital Amp Power Stage RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TAS5112ADFDRG4 功能描述:音頻放大器 Digital Amp Power Stage RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*