- 您現在的位置：買賣IC網 > PDF目錄98159 > TAS5012PFBG4 (TEXAS INSTRUMENTS INC) SPECIALTY CONSUMER CIRCUIT, PQFP48 PDF資料下載
參數資料
| 型號： | TAS5012PFBG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| 封裝： | PLASTIC, TQFP-48 |
| 文件頁數： | 16/18頁 |
| 文件大小： | 245K |
| 代理商： | TAS5012PFBG4 |
TAS5012
SLES006A SEPTEMBER 2001 REVISED DECEMBER 2001
7
www.ti.com
functional description (continued)
reset
The reset signal for the TAS5012 must be applied whenever toggling the M_S, DBSPD signal. This reset is
asynchronous. See Figure 3 for reset timing. To initiate the reset sequence the RESET pin is asserted low. As long
as the pin is held low, the chip is in the reset state. During this reset time the PWM outputs are hard-muted (P-outputs
held low and M-outputs held high) and the PWM outputs valid pins (VALID_L. VALID_R) are held low. Assuming PDN
is high, the rising edge of the reset pulse begins chip initialization. After the initialization time, the TAS5012 begins
normal operation.
Initialization
Normal
Operation
RESET
PDN
Normal Operation
5 ms max
VALID_L
VALID_R
Figure 3. Reset Timing
power down
When PDN is low (see Figure 4), both the PLL and the oscillator are shut down. Note that power down is an
asynchronous operation. To place the device in total power-down mode, both RESET and PDN must be held low.
As long as these pins are held low, the chip is in the power-down state and the PWM outputs are hard muted with
the P outputs held low and the M outputs held high. To place the device back into normal mode, see the power up
section.
NOTE: In order for the dynamic logic to be properly powered down, the clocks should not be stopped before the PDN
pin goes low. Otherwise, the device may drain additional supply current.
Initialization
Chip
Power-Down
PDN and RESET
Normal Operation
Normal
Operation
VALID
Figure 4. Power-Down Timing
mute
The TAS5012 provides a mute function that is used when the MUTE pin is asserted low. See Table 2 for mute
description. This mute is a quiet mute; that is, the mute is accomplished by outputting a zero value waveform in which
both sides of the differential PWM outputs have a 50% duty cycle (see Figure 5 for mute timing).
Table 2. Mute Description
MUTE
P OUTPUTS
M OUTPUTS
DESCRIPTION
0
50% duty cycle
Mute
1
DATA
Normal operation
相關PDF資料 |
PDF描述 |
|---|---|
| TAS5012PFBRG4 | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| TAS5012IPFBG4 | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| TAS5015IPFBR | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| TAS5015PFB | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| TAS5015PFBR | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TAS5012PFBR | 功能描述:音頻 DSP Digital Audio PWM Processor RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube |
| TAS5012PFBRG4 | 功能描述:音頻 DSP Digital Audio PWM Processor RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube |
| TAS5015 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:TRUE DIGITAL AUDIO AMPLIFIER TAS5015 DIGITAL AUDIO PWM PROCESSOR |
| TAS5015_06 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:TRUE DIGITAL AUDIO AMPLIFIER DIGITAL AUDIO PWM PROCESSOR |
| TAS5015IPFB | 制造商:TI 制造商全稱:Texas Instruments 功能描述:TRUE DIGITAL AUDIO AMPLIFIER TAS5015 DIGITAL AUDIO PWM PROCESSOR |
發布緊急采購，3分鐘左右您將得到回復。