- 您現在的位置：買賣IC網 > PDF目錄98154 > TA7259F BRUSHLESS DC MOTOR CONTROLLER, 1.2 A, PDSO22 PDF資料下載
參數資料
| 型號： | TA7259F |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 1.2 A, PDSO22 |
| 封裝： | 0.450 INCH, 1 MM PITCH, PLASTIC, HSOP-20/22 |
| 文件頁數： | 18/18頁 |
| 文件大?。?/td> | 423K |
| 代理商： | TA7259F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁
TA7259P/F/FG
2006-4-14
9
Notes on handling the IC
Motor drive ICs are easily affected by parasitic vibration and unnecessary feedback. This is because the
number of high impedance pins, such as position sensing inputs and control signal inputs, is large, and the
output current value is high and switched.
Moreover, because it is coil loading, care must be taken not to allow the impulse to destroy the IC during
ON/OFF switching. Especially when using a high voltage supply (Vcc is 18V or more), care must be taken not to
apply voltage and current to the output transistor which exceed the specification. Use of a supply voltageof 18V
or less is recommended. Pay particular attention to the notes above when using a supply voltage over 18V.
(1) Notes in designing reliability
) Do not expose the output transistor of the internal IC to high voltage and current,
especially, in motor lock status, ON/OFF switching of Vcc, output short-circuiting, etc.)
) The output condenser for ringing absorption should be as small as possible because the output
transistor can be destroyed by the charge-discharge current of this condenser. When there is a
problem, adjusting the capacity of the condenser, the connecting position and the connecting method
(delta or star), and inserting a series resistor (of a few to dozens of ) to the condenser and series
should provide the oscillating protection explained later.
) In mounting to the print-board, do not stress the FIN, and solder for only a few seconds at 260 .
) Using the large earth area of the print-board to release heat from the FIN is effective in ensuring
reliability.
(2) Notes in wiring
To protect from parasitic vibration, design the print-pattern following the method below.
)
The output coil current path must be separated from other GND lines because a switched high
current flows in this path. It is very important that the line (RF pin RF resister GND) should not
be of a common impedance with other circuits.
If the above is impossible or the oscillation cannot be removed completely, connect the condenser
(0.01 0.1F) and RF in parallel.
2.
TA7259P/F/FG
Avoid common impedance with other circuits
Fig. 2
相關PDF資料 |
PDF描述 |
|---|---|
| TA7279P | BRUSH DC MOTOR CONTROLLER, 3 A, PDIP16 |
| TA7289FG | STEPPER MOTOR CONTROLLER, 0.8 A, PDSO22 |
| TA7326P | TIMER, PSIP7 |
| TA7343AP | SPECIALTY CONSUMER CIRCUIT, PSIP9 |
| TA7368F | 0.61 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TA7259FG | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:3-PHASE BRUSHLESS DC MOTOR DRIVER IC |
| TA7259P | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:DC MOTOR DRIVER IC |
| TA7259P(5) | 制造商:Toshiba America Electronic Components 功能描述: |
| TA7259P(LB) | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:DC MOTOR DRIVER IC |
| TA7259P_06 | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:3-PHASE BRUSHLESS DC MOTOR DRIVER IC |
發布緊急采購，3分鐘左右您將得到回復。