- 您現在的位置：買賣IC網 > PDF目錄384945 > TA2021B (Electronic Theatre Controls, Inc.) STEREO 25W (4OHM) CLASS-T DIGITAL AUDIO AMPLIFIER DRIVER USING DIGITAL POWER PROCESSING (DPP) TECHNOLOGY PDF資料下載
參數資料
| 型號： | TA2021B |
| 廠商： | Electronic Theatre Controls, Inc. |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEREO 25W (4OHM) CLASS-T DIGITAL AUDIO AMPLIFIER DRIVER USING DIGITAL POWER PROCESSING (DPP) TECHNOLOGY |
| 中文描述： | 立體聲25瓦（4Ω）類- T的數字音頻放大器驅動程序使用數字功率處理（民進黨）科技 |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 268K |
| 代理商： | TA2021B |
Tripath Technology, Inc. - Technical Information
10
TA2021B – 3.0/04.03
connected to the FAULT pin, the HIGH output of the FAULT pin will toggle the MUTE pin and
automatically reset the fault condition.
Overload (Output Active Low)
The OVERLOADB pin is a 5V logic active-low output. When low, it indicates that the level of the
input signal has overloaded the amplifier resulting in increased distortion at the output. The
OVERLOADB signal can be used to control a distortion indicator light or LED through a simple
buffer circuit.
Sleep Pin (Input Active High)
The SLEEP pin is a 5V logic input that, when pulled high (>3.5V), puts the part into a low
quiescent current mode. This pin is internally clamped by a zener diode to approximately 6V thus
allowing the pin to be pulled up through a large valued resistor (1M
recommended, 100K
minimum) to VDD. To disable SLEEP mode, the sleep pin should be grounded.
Fault Pin (Output Active High)
The FAULT pin is a 5V logic output that indicates various fault conditions within the device.
These conditions include: low supply voltage, low charge pump voltage, low 5V regulator voltage,
over current at any output, and junction temperature greater than approximately 155
°
C. The
FAULT output is capable of directly driving an LED through a series 2K
resistor. If the FAULT
pin is connected directly to the MUTE input an automatic reset will occur in the event of an over-
current condition.
Performance Measurements of the TA2021B
The TA2021B operates by generating a high frequency switching signal based on the audio input.
This signal is sent through an external low-pass filter that recovers an amplified version of the
audio input
.
The frequency of the switching pattern is spread spectrum in nature and typically
varies between 100kHz and 1MHz (which is well above the 20Hz – 20kHz audio band). The
pattern itself does not alter or distort the audio input signal, but it does introduce some inaudible
components.
The measurements of certain performance parameters, particularly noise related specifications
such as THD+N, are significantly affected by the design of the low-pass filter used on the output
as well as the bandwidth setting of the measurement instrument used. Unless the filter has a
very sharp roll-off just beyond the audio band or the bandwidth of the measurement instrument is
limited, some of the inaudible noise components introduced by the TA2021B amplifier switching
pattern will degrade the measurement.
One feature of the TA2021B is that it does not require large multi-pole filters to achieve excellent
performance in listening tests, usually a more critical factor than performance measurements.
Though using a multi-pole filter may remove high-frequency noise and improve THD+N type
measurements (when they are made with wide-bandwidth measuring equipment), these same
filters degrade frequency response. The TA2021B Evaluation Board uses the Application/Test
Circuit of this data sheet, which has a simple two-pole output filter and excellent performance in
listening tests. Measurements in this data sheet were taken using this same circuit with a limited
bandwidth setting in the measurement instrument.
相關PDF資料 |
PDF描述 |
|---|---|
| TA2024 | Stereo 10W (4з) Class-T⑩ Digital Audio Amplifier using Digital Power Processing⑩ Technology |
| TA2050 | GROUND ISOLATOR IC |
| TA2057 | AM/FM IF+FM ST DET (FOR DIGITAL TUNING SYSTEM) |
| TA2099F | AM/FM IF+FM STEREO DETECTOR (FOR DIGITAL TUNING SYSTEM) |
| TA2099N | AM/FM IF+FM STEREO DETECTOR (FOR DIGITAL TUNING SYSTEM) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TA2022 | 制造商:TRIPATH 制造商全稱:TRIPATH 功能描述:STEREO 90W (4з) CLASS-T⑩ DIGITAL AUDIO AMPLIFIER DRIVER USING DIGITAL POWER PROCESSING (DPP⑩) TECHNOLOGY |
| TA202216 | 制造商:POWEREX 制造商全稱:Powerex Power Semiconductors 功能描述:Phase Control SCR (1600-1800 Amperes Avg 100-2200 Volts) |
| TA20221603DH | 功能描述:SCR PHASE CTRL 2200V 1600A RoHS:是 類別:半導體模塊 >> SCR 系列:- 其它有關文件:SCR Module Selection Guide 標準包裝:10 系列:- 結構:串聯 - SCR/二極管 SCR 數目，二極管:1 SCR，1 個二極管 電壓 - 斷路:1600V 電流 - 柵極觸發電流 (Igt)（最大）:150mA 電流 - 導通狀態 (It (AV))（最大）:95A 電流 - 導通狀態 (It (RMS))（最大）:210A 電流 - 非重復電涌，50、60Hz (Itsm):1785A，1870A 電流 - 維持(Ih):250mA 安裝類型:底座安裝 封裝/外殼:ADD-A-PAK（3 + 2） 包裝:散裝 其它名稱:*IRKL92/16AIRKL92/16IRKL92/16-ND |
| TA20221603DN | 制造商:n/a 功能描述:Power Semiconductor |
| TA202218 | 制造商:POWEREX 制造商全稱:Powerex Power Semiconductors 功能描述:Phase Control SCR (1600-1800 Amperes Avg 100-2200 Volts) |
發布緊急采購，3分鐘左右您將得到回復。