參數資料
型號: TA2020-020
廠商: Electronic Theatre Controls, Inc.
元件分類: 運動控制電子
英文描述: Stereo 20W (4з) Class-T Digital Audio Amplifier using Digital Power Processing Technology
中文描述: 立體聲20瓦(4з)類- T數字音頻放大器采用數字電源處理技術
文件頁數: 9/13頁
文件大?。?/td> 293K
代理商: TA2020-020
T E C H N I C A L I N F O R M A T I O N
TA2020-020, Rev. 4.0, 09.00
9 of 13
Amplifier Gain
The gain of the TA2020-020 is set by the ratio of two external resistors, R
I
and R
F
, and is given by
the following formula:
R
12
V
where V
I
is the input signal level and V
O
is the differential output signal level across the speaker.
20 watts of RMS output power results from an 8.944 V RMS signal across a four-ohm speaker load.
If R
F
= R
I
, then 20 Watts will be achieved with 0.745 V RMS of input signal.
)
W
20
4
(
)
P
R
(
V
944
.
O
L
RMS
=
=
Protection Circuits
The TA2020-020 is guarded against over-temperature and over-current conditions. When the
device goes into an over-temperature or over-current state, the FAULT pin goes to a logic HIGH
state indicating a fault condition. When this occurs, the amplifier is muted, all outputs are TRI-
STATED, and will float to 1/2 of V
DD
.
Over-temperature Protection
An over-temperature fault occurs if the junction temperature of the part exceeds approximately
155
°
C. The thermal hysteresis of the part is approximately 45
°
C, therefore the fault will
automatically clear when the junction temperature drops below 110
°
C.
Over-current Protection
An over-current fault occurs if more than approximately 7 amps of current flows from any of the
amplifier output pins. This can occur if the speaker wires are shorted together or if one side of the
speaker is shorted to ground. An over-current fault sets an internal latch that can only be cleared if
the MUTE pin is toggled or if the part is powered down. Alternately, if the MUTE pin is connected to
the FAULT pin, the HIGH output of the FAULT pin will toggle the MUTE pin and automatically reset
the fault condition.
Overload
The OVERLOADB pin is a 5V logic output. When low, it indicates that the level of the input signal
has overloaded the amplifier resulting in increased distortion at the output. The OVERLOADB
signal can be used to control a distortion indicator light or LED through a simple buffer circuit.
Sleep Pin
The SLEEP pin is a 5V logic input that when pulled high (>3.5V) puts the part into a low quiescent
current mode. This pin is internally clamped by a zener diode to approximately 6V thus allowing the
I
F
I
O
R
V
=
B
相關PDF資料
PDF描述
TA2021B STEREO 25W (4OHM) CLASS-T DIGITAL AUDIO AMPLIFIER DRIVER USING DIGITAL POWER PROCESSING (DPP) TECHNOLOGY
TA2024 Stereo 10W (4з) Class-T⑩ Digital Audio Amplifier using Digital Power Processing⑩ Technology
TA2050 GROUND ISOLATOR IC
TA2057 AM/FM IF+FM ST DET (FOR DIGITAL TUNING SYSTEM)
TA2099F AM/FM IF+FM STEREO DETECTOR (FOR DIGITAL TUNING SYSTEM)
相關代理商/技術參數
參數描述
TA202016 制造商:POWEREX 制造商全稱:Powerex Power Semiconductors 功能描述:Phase Control SCR (1600-1800 Amperes Avg 100-2200 Volts)
TA20201603DH 功能描述:SCR PHASE CTRL 2000V 1600A RoHS:是 類別:半導體模塊 >> SCR 系列:- 其它有關文件:SCR Module Selection Guide 標準包裝:10 系列:- 結構:串聯 - SCR/二極管 SCR 數目,二極管:1 SCR,1 個二極管 電壓 - 斷路:1600V 電流 - 柵極觸發電流 (Igt)(最大):150mA 電流 - 導通狀態 (It (AV))(最大):95A 電流 - 導通狀態 (It (RMS))(最大):210A 電流 - 非重復電涌,50、60Hz (Itsm):1785A,1870A 電流 - 維持(Ih):250mA 安裝類型:底座安裝 封裝/外殼:ADD-A-PAK(3 + 2) 包裝:散裝 其它名稱:*IRKL92/16AIRKL92/16IRKL92/16-ND
TA202018 制造商:POWEREX 制造商全稱:Powerex Power Semiconductors 功能描述:Phase Control SCR (1600-1800 Amperes Avg 100-2200 Volts)
TA20201803DH 制造商:n/a 功能描述:Power Semiconductor
TA2021-100 制造商:未知廠家 制造商全稱:未知廠家 功能描述:STEREO 100W (4-ohm) CLASS-T DIGITAL AUDIO AMPLIFIER DRIVER USING DPP-TM TECHNOLOGY