參數資料
型號： TA1318NG
元件分類： 消費家電
英文描述： SPECIALTY CONSUMER CIRCUIT, PDIP24
封裝： 0.300 INCH, 1.78 MM PITCH, PLASTIC, SDIP-24
文件頁數： 7/41頁
文件大?。?/td> 896K
代理商： TA1318NG
TA1318NG
2005-09-08
15
Read Mode
POR (Power on reset)
(0): Status read (at second data read and subsequent)
(1): Power on (at first data read)
HD-IN (Input signal self-check result)
Detects HD or H-SYNC input signal selected by INPUT SW.
(0): No signal input (1): Signal input
V FREQ DET (Vertical frequency of SYNC or VD input selected by FREQ DET SW)
(0000000)(0001100): No-VD
(0001101) : Vicinity of 162 Hz
(1111110) : Vicinity of 17 Hz
How to calculate vertical frequency (X):
Convert V-FREQ DET read data into decimal and define the resulting value as Y.
Where H-FREQUENCY is 15.75 kHz/31.5 kHz, Z = 476.2 s
Where H-FREQUENCY is 33.75 kHz/45 kHz, Z = 474.1 s
Vertical frequency (X) = 1 ÷ (Y × Z) [Hz]
Error of Y is +1, 0. If vertical frequency is 162 Hz or more, the frequency cannot be accurately
measured. Time constant used to separate V.SYNC from integrated C.SYNC is 9 s (error: ±1 s).
H FREQ DET (Horizontal frequency of SYNC or HD input selected by FREQ DET SW)
(0000000): No signal input (1111110): 53 kHz or more
How to calculate horizontal frequency (X):
X, Y, and Z are defined same as for V FREQ.
Horizontal frequency (X) = Y ÷ (5 × Z) [kHz]
Error of Y is +1, 0. If horizontal frequency is 53 kHz or more, the frequency cannot be accurately
measured. When V-SYNC or VD is not input, horizontal frequency cannot be measured, resulting in
data = (0000000).
Note 1: The start trigger for frequency counting is the internal reset-pulse made from ACK of 2nd byte in BUS
read mode. The counting period is between the first V-sync (VD) and the second V-sync (VD) after the
trigger.
The counted data will have +1 or 0 error according to the read timing.
To assume stable data reading;
1. Set BUS reading interval more than 60 ms.
2. Don’t use the first data because it is unsettled.
are recommended.
Note 2: Make data (1111111) invalid in your programs. This data may be obtained in case the trigger pulse and
the V-sync (VD) are simultaneous.
Note 3:Make following data invalid in your programs. These data are obtained when the pin voltage of SYNC-IN
pin is higher than sync separation level and while any signal is not input into SYNC-IN pin.
(H FREQUENCY DET, V FREQUENCY DET)
= (0000001, 0001101), (0000001, 0001110), (0000111, 1111111), (0000000, 1111111),
and (0000101, 1111111)
Decision algorithm (detection range, detection times and so on) should be determined under
consideration of Note 1, Note 2 and the other factors such as signal strength, existence of ghost signal,
H-AFC stability, I2C BUS data transmission and so on via prototype TV set evaluation.
Read Timing
V-SYNC or VD
More than 60 ms
Counting period 1
(to Data 1)
Counting period 2
(to Data 2)
Start trigger 1
Data 1 and
Start trigger 2
Data 2 and
Start trigger 3
相關PDF資料
PDF描述
TA1318N SPECIALTY CONSUMER CIRCUIT, PDIP24
TA1326FNG SPECIALTY CONSUMER CIRCUIT, PDSO16
TA1360AFG SPECIALTY CONSUMER CIRCUIT, PQFP80
TA1360ANG SPECIALTY CONSUMER CIRCUIT, PDIP56
TA1370FG SYNC SEPARATOR IC, PDSO30
相關代理商/技術參數
參數描述
TA132 制造商:pico Technology 功能描述:Probe; Oscilloscope; 150 MHz; 1.2 m; 1:1/10:1
TA1322FN 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:DOWB-CONVERTER IC WITH PLL FOR SATELLITE TUNER
TA1326FNG 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:UHF BAND RF MODULATOR IC FOR VTRS
TA133 制造商:pico Technology 功能描述:Probe; Oscilloscope; 500 MHz; 1.2 m; x10; Used w/ PicoScope 6000 制造商:pico Technology 功能描述:PASSIVE PROBE, 500MHZ, 10X ATTENUATION; Test Probe Type:Oscilloscope; For Use With:PicoScope 6404 Oscilloscopes; Bandwidth:500MHz; Features:10x Attenuation ;RoHS Compliant: NA
TA-133.330MBD-T 功能描述:標準時鐘振蕩器 133.330MHz 3.3V 25 ppm -40C to 85C RoHS:否 制造商:AVX 產品:Standard Clock Oscillators 封裝 / 箱體:7 mm x 5 mm 頻率:75 MHz 頻率穩定性:50 PPM 電源電壓:2.5 V 負載電容: 端接類型:SMD/SMT 最小工作溫度:0 C 最大工作溫度:+ 70 C 輸出格式:LVDS 尺寸: 封裝:Reel 系列:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*