- 您現在的位置：買賣IC網 > PDF目錄361357 > T63H0008A (TM Technology, Inc.) Li-Ion/Polymer Battery for one-cell Protector PDF資料下載
參數資料
| 型號： | T63H0008A |
| 廠商： | TM Technology, Inc. |
| 英文描述： | Li-Ion/Polymer Battery for one-cell Protector |
| 中文描述： | Li-Ion/Polymer電池單細胞保護 |
| 文件頁數： | 7/20頁 |
| 文件大?。?/td> | 341K |
| 代理商： | T63H0008A |
TE
CH
tm
(4) Measurement Condition 4, Measurement Circuit 2
T63H0008A
TM Technology, Inc. reserves the right
P. 7
Publication Date: Dec. 2003
to change products or specifications without notice. Revision:A
(Charger detection voltage, abnormal charge current detection voltage)
Set V1=1.8V and V2=0V. Increase V1 gradually until V1=VDET2 +(VHDT2 /2), then decrease V2 from 0
V gradually. The voltage between V- and VSS when VDO goes “H” from “L” is the charger detection
voltage (VDET5). Charger detection voltage can be measured only in the product whose over-discharge
hysteresis VHDT2 0.
Set V1=3.5V and V2=0V, Decrease V2 from 0 V gradually. The voltage between V- and VSS when VCO
goes “L” from “H” is the abnormal charge current detection voltage. The abnormal charge current detection
voltage has the same value as the charger detection voltage (VDET5).
(5) Measurement Condition 5, Measurement Circuit 2
(Normal operation current consumption, Power-down current consumption)
Set V1=3.5V and V2=0V under normal condition. The current IDD flowing through VDD pin is the
normal operation consumption current (IDD).
Set V1=V2=1.5V under over-discharge condition. The current IDD flowing through VDD pin is the
power-down current consumption (ISB).
(6) Measurement Condition 6, Measurement Circuit 3
(Internal resistance between V- and VDD, Internal resistance between V- and VSS)
Set V1=1.8V and V2=0V. The resistance between V- and VDD is the internal resistance (RV-D) between
V- and VDD. Set V1=3.5V and V2=1.0V. The resistance between V- and VSS is the internal resistance
(RV-S) between V- and VSS.
(7) Measurement Condition 7, Measurement Circuit 4
(COUT pin H resistance, COUT pin L resistance)
Set V1=3.5V, V2=0V and V3=3.0V. COUT pin resistance is the COUT pin H resistance (RCOUTH ).
Set V1=4.5V, V2=0V and V3=0.5V. COUT pin resistance is the COUT pin L resistance (RCOUTL )
.
(8) Measurement Condition 8, Measurement Circuit 4
(DOUT pin H resistance, DOUT pin L resistance)
Set V1=3.5V, V2=0V and V4=3.0V. DOUT pin resistance is the DOUT pin H resistance (RDOUTH ).
Set V1=1.8V, V2=0V and V4=0.5V. DOUT pin resistance is the DOUT pin L resistance (RDOUTL ).
(9) Measurement Condition 9, Measurement Circuit 5
(Overcharge detection delay time, Over-discharge detection delay time)
The overcharge detection delay time (tVDET1) is the time needed for VCO to change from "H" to "L" just
after the V1 rapid increase within 10us from the overcharge detection voltage (VDET1) - 0.2V to the
相關PDF資料 |
PDF描述 |
|---|---|
| T63H0008A-AX | Li-Ion/Polymer Battery for one-cell Protector |
| T63H0008A-BX | Li-Ion/Polymer Battery for one-cell Protector |
| T63H0008A-CX | Li-Ion/Polymer Battery for one-cell Protector |
| T63H0008A-DX | Li-Ion/Polymer Battery for one-cell Protector |
| T66H0001A | 240 output LCD Segment/Common Driver IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| T63H0008A-AX | 制造商:TMT 制造商全稱:TMT 功能描述:Li-Ion/Polymer Battery for one-cell Protector |
| T63H0008A-BX | 制造商:TMT 制造商全稱:TMT 功能描述:Li-Ion/Polymer Battery for one-cell Protector |
| T63H0008A-CX | 制造商:TMT 制造商全稱:TMT 功能描述:Li-Ion/Polymer Battery for one-cell Protector |
| T63H0008A-DX | 制造商:TMT 制造商全稱:TMT 功能描述:Li-Ion/Polymer Battery for one-cell Protector |
| T63XA-100-10-D06 | 制造商:Vishay Roederstein 功能描述:RES TRMR 100 OHM 10% 1/4W 13TURN 1.8MM PIN TH - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。