
TE
CH
tm
T63H0006B 
Features
 Low supply current :  
  operating current : 3.0uA (TYP.) 
  Standby current  : 0.15uA (TYP.) 
  (after detecting over-discharge)
 High accuracy detector Threshold : 
  Over-charge detector (Topt=25oC) +/- 25mV 
 Variety of detector threshold
 : 
-Over-charge detector threshold
4.225V to 4.375V step of 0.005V 
-Over-discharge detector threshold
2.4V to 2.6V step of 0.005V 
 Built in protection circuit
 : 
  -Excess current protection
0.13V to 0.17V step of  0.04V
  -
Accuracy ±15% 
 Output delay of over charge
 : 
  Time delay VDD=3.6V to 4.3V
110ms
  (The result was measured from T63H0006B-AX) 
 Output delay of over-discharg : 
VDD=3.6V to 2.4V with built-in capacitor
10ms 
 Small package
SOT23-6/6-pin
Part Number Examples 
                                                                      T63H0006B
Li-Ion Battery Protector
TM Technology Inc. reserves the right
P. 1                                    
Publication Date: JUN. 2004 
to change products or specifications without notice.                                                                         Revision:B
Part No. 
Over 
charge 
detection 
voltage 
Over 
charge 
release 
 voltage 
marking Pack type 
T63H0006B-AX 
T63H0006B-BX 
T63H0006B-CX 
T63H0006B-DX 
…note 
Note : New model version and specific 
characteristics may be order by customer. 
4.25V 
4.35V 
4.30V 
4.28V 
…. 
4.05V 
4.15V 
4.10V 
4.08V 
…. 
006A 
006B 
006C 
006D 
SOT-23-6 
SOT-23-6 
SOT-23-6 
SOT-23-6 
…. 
General Description
    The 
T63H0006B 
over-charge / discharge of rechargeable one-cell 
Lithium-ion(Li+) excess load current, further 
include a short circuit protector for preventing 
large external short circuit current. 
     Each of these IC is composed of three voltage 
detectors, a reference unit, a delay circuit, a short 
circuit protector, and a logic circuit. When 
charging voltage crosses the detector threshold 
from a low value to value higher than VDET1, the 
output of Cout pin, the output of over-charge 
detector/VD1, switches to low level, charger’s 
negative pin level. After detecting over-charge the 
VD1 can be reset and the output of Cout becomes 
high when the VDD voltage is coming down to a 
level lower than “VREL1”, or when a kind of 
loading is connected to VDD after a charger is 
disconnected from the battery pack while the VDD 
level is in between “VDET1” and “VREL1” in the 
T63H0006B. 
     The output of Dout pin, the output of 
over-discharge detector/VD2, switches to low 
level after internally fixed delay time passed, when 
discharging voltage crosses the detector threshold 
from a high value lower than VDET2. After 
T63H0006B detect the over-discharge voltage, 
connect a charger to the battery pack, and when the 
battery supply voltage becomes higher than the 
over-discharge detector threshold, VD2 is released 
and the voltage of Dout becomes “H” level. 
    An excess load current can be sensed and cut off 
after internally fixed delay time passed through the 
built in excess current detector, VD3 with Dout 
being enabled to low level. Once after detecting 
excess current, the VD3 is released and Dout level 
switches to high by detaching a battery pack from a 
load system. 
    Further, short circuit protector makes Dout level 
to low immediately with external short circuit 
current and re-moving external short circuit leads 
Dout level to high. After detecting over-discharge, 
supply current will be kept extremely low by halt 
some internal circuits operation. The output delay 
of over-charge detectors can be set by connecting 
external capacitors. Output type of Cout and Dout 
are CMOS. 6-pin, SOT23-6 is available. 
is 
protection 
IC 
for