- 您現在的位置：買賣IC網 > PDF目錄383875 > T530X337M010AS (Texas Instruments, Inc.) 60-A, 3.3/5-V INPUT, NONISOLATED WIDE-OUTPUT ADJUST POWER MODULE PDF資料下載
參數資料
| 型號： | T530X337M010AS |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | 60-A, 3.3/5-V INPUT, NONISOLATED WIDE-OUTPUT ADJUST POWER MODULE |
| 中文描述： | 60甲，3.3/5-V輸入，非隔離寬輸出調節電源模塊 |
| 文件頁數： | 5/24頁 |
| 文件大?。?/td> | 947K |
| 代理商： | T530X337M010AS |
www.ti.com
DEVICE INFORMATION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
PTHXX040W
(Top View)
16
PTH04040W
SLTS238A–SEPTEMBER 2005–REVISED FEBRUARY 2006
TERMINAL FUNCTIONS
TERMINAL
DESCRIPTION
NAME
NO.
1, 3, 5, 10, 13,
16
2, 4, 6
9, 12, 15
This is the common ground connection for the V
I
and V
O
power connections. It is also the 0 Vdc
reference for the control inputs.
The positive input voltage power node to the module, which is referenced to common GND.
The regulated positive power output with respect to the
GND
node.
The Inhibit pin is an open-collector/drain negative logic input that is referenced to GND. Applying a
lowlevel ground signal to this input disables the module’s output and turns off the output voltage. When
the Inhibit control is active, the input current drawn by the regulator is significantly reduced. If the Inhibit
pin is left open-circuit, the module produces an output whenever a valid input source is applied. Do not
place an external pull-up on this pin.
A 1%, 0.05-W resistor must be connected between this pin and GND to set the output voltage higher
than the minimum value. The set-point range for the output voltage is from 0.8 V to 2.5 V. The resistor
required for a given output voltage may be calculated from the following formula. If left open circuit, the
module output defaults to its lowest output voltage value. For further information on the adjustment
and/or trimming of the output voltage, see the related Application Information section.
Note: The
specification table gives the preferred resistor values for a number of standard output voltages
.
The sense inputs allow the regulation circuit to compensate for voltage drop between the module and
the load. For optimal voltage accuracy, +Sense should be connected to V
O
. If it is left open, a low-value
internal resistor ensures that the output remains in regulation.
For optimal voltage accuracy, –Sense should be connected to the ground return at the load. If it is left
open, a low-value internal resistor ensures that the output remains in regulation.
Connecting a resistor from this pin to signal ground allows the
on
threshold of the input undervoltage
lockout (UVLO) to be adjusted higher than the default value. The hysterisis can also be independenly
reduced by connecting a second resistor from this pin to V
I
. For further information, see the Application
Information section.
This is an analog control input that allows the output voltage to follow another voltage during power up
and power down sequences. The pin is active from 0 V, up to the nominal set-point voltage. Within this
range, the module output follows the voltage at the Track pin on a volt-for-volt basis. When the control
voltage is raised above this range, the module regulates at its nominal output voltage. If unused, this
input should be connected to V
I
for a faster power up. For further information, see the related
Application Information section.
When this input is asserted to GND, the output voltage is decreased by 5% from the nominal. The input
requires an open-collector (open-drain) interface. It is
not
TTL compatible. A lower percent change can
be accommodated with a series resistor. For further information, see the related Application Information
section.
When this input is asserted to GND, the output voltage is increased by 5%. The input requires an open
collector (open-drain) interface. It is
not
TTL compatible. The percent change can be reduced with a
series resistor. For further information, see the related Application Information section.
GND
V
I
V
O
Inhibit
(1)
7
V
O
Adjust
17
+Sense
11
–Sense
14
UVLO Prog
8
Track
18
Margin Down
(1)
20
Margin Up
(1)
19
(1)
Denotes negative logic: Open = Normal operation; Ground = Function active
5
Submit Documentation Feedback
相關PDF資料 |
PDF描述 |
|---|---|
| T530X477M006AS | 60-A, 3.3/5-V INPUT, NONISOLATED WIDE-OUTPUT ADJUST POWER MODULE |
| T5504 | Quad PCM Codecs with Filters(帶濾波器的四PCM編解碼器) |
| T70HF10 | POWER RECTIFIER DIODES |
| T70HF100 | POWER RECTIFIER DIODES |
| T70HF120 | POWER RECTIFIER DIODES |
相關代理商/技術參數 |
參數描述 |
|---|---|
| T530X337M010ASE006 | 功能描述:CAP TANT 330UF 10V 20% 2917 RoHS:是 類別:電容器 >> 鉭 系列:KO Cap T530 標準包裝:1,000 系列:TANTAMOUNT® 695D 電容:3.3µF 電壓 - 額定:50V 容差:±20% ESR（等效串聯電阻）:3.2 歐姆 類型:保形涂層 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:2414（6034 公制） 尺寸/尺寸:0.236" L x 0.135" W（6.00mm x 3.43mm） 高度 - 座高（最大）:0.085"（2.16mm） 引線間隔:- 制造商尺寸代碼:F 特點:通用 包裝:帶卷 (TR) 壽命@溫度:- |
| T530X337M010ASE010 | 功能描述:CAP TANT 330UF 10V 20% 2917 RoHS:否 類別:電容器 >> 鉭 系列:KO Cap T530 標準包裝:1,000 系列:TANTAMOUNT® 695D 電容:3.3µF 電壓 - 額定:50V 容差:±20% ESR（等效串聯電阻）:3.2 歐姆 類型:保形涂層 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:2414（6034 公制） 尺寸/尺寸:0.236" L x 0.135" W（6.00mm x 3.43mm） 高度 - 座高（最大）:0.085"（2.16mm） 引線間隔:- 制造商尺寸代碼:F 特點:通用 包裝:帶卷 (TR) 壽命@溫度:- |
| T530X337M010AT | 功能描述:鉭質電容器-SMD聚合物 330.UF 10.0V RoHS:否 制造商:Kemet 電容:33 uF 電壓額定值:50 V ESR:40 mOhms 容差:20 % 工作溫度范圍: 外殼代碼 - in:2917 外殼代碼 - mm:7343 高度:4 mm 制造商庫存號:X Case 系列:T543 產品: 封裝:Reel |
| T530X337M010ATE004 | 功能描述:鉭質電容器-SMD聚合物 330uF 10volts 20% RoHS:否 制造商:Kemet 電容:33 uF 電壓額定值:50 V ESR:40 mOhms 容差:20 % 工作溫度范圍: 外殼代碼 - in:2917 外殼代碼 - mm:7343 高度:4 mm 制造商庫存號:X Case 系列:T543 產品: 封裝:Reel |
| T530X337M010ATE005 | 功能描述:鉭質電容器-SMD聚合物 330uF 10volts 20% RoHS:否 制造商:Kemet 電容:33 uF 電壓額定值:50 V ESR:40 mOhms 容差:20 % 工作溫度范圍: 外殼代碼 - in:2917 外殼代碼 - mm:7343 高度:4 mm 制造商庫存號:X Case 系列:T543 產品: 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。