hbwhelp@micrel.com or (408) 955-1690 7 Functional Descr" />
參數資料
型號: SY89467UHY
廠商: Micrel Inc
文件頁數: 13/15頁
文件大?。?/td> 0K
描述: IC CLK BUFF MUX 2:20 2GHZ 64TQFP
標準包裝: 160
系列: Precision Edge®
類型: 扇出緩沖器(分配),多路復用器
電路數: 1
比率 - 輸入:輸出: 2:20
差分 - 輸入:輸出: 是/是
輸入: CML,LVDS,PECL
輸出: LVPECL
頻率 - 最大: 2GHz
電源電壓: 2.375 V ~ 3.6 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 64-TQFP 裸露焊盤
供應商設備封裝: 64-EP-TQFP
包裝: 托盤
產品目錄頁面: 1083 (CN2011-ZH PDF)
其它名稱: 576-2085
SY89467UHY-ND
Micrel, Inc.
SY89467U
April 2008
M9999-040808-C
hbwhelp@micrel.com or (408) 955-1690
7
Functional Description
Clock Select (SEL)
SEL is an asynchronous TTL/CMOS compatible input
that selects one of the two input signals. An internal
25k
pull-up resistor defaults the input to logic HIGH if
left open. Input switching threshold is VCC/2. Refer to
Figure 1a.
Fail-Safe Input (FSI)
The input includes a special failsafe circuit to sense
the amplitude of the input signal and to latch the
outputs when there is no input signal present, or when
the amplitude of the input signal drops sufficiently
below
100mVPK,
typically
30mVPK.
Maximum
frequency of the SY89467U is limited by the FSI
function. Refer to Figure 1b.
Input Clock Failure Case
If the input clock fails to a floating, static, or extremely
low signal swing such that the voltage across the input
pair is significantly less than 100mV, FSI function will
eliminate a metastable condition and latch the outputs
to the last valid state. No ringing and no undetermined
state will occur at the output under these conditions.
The output recovers to normal operation once the
input signal returns to a valid state with a typical swing
greater than 30mV.
Note that the FSI function will not prevent duty cycle
distortion in case of a slowly deteriorating (but still
toggling) input signal. Due to the FSI function, the
propagation delay will depend on the rise and fall time
of the input signal and on its amplitude.
Output Enable (OE)
OE is a synchronous TTL/CMOS compatible input that
enables/disables the outputs based upon the input to
this pin. The enable function is synchronous so that
the clock outputs will be enabled or disabled following
a rising and a falling edge of the input clock. Refer to
Figure 1c. Internal 25k
pull-up resistor defaults the
input to logic HIGH if left open. Input switching
threshold is VCC/2.
相關PDF資料
PDF描述
LTC2630ISC6-LZ8#TRPBF IC DAC 8BIT SRL SC70-6
SY89468UHY IC CLOCK BUFFER MUX 2:20 64-TQFP
LTC6993MPS6-3#TRMPBF IC MULTIVIBRATOR MONO TSOT23-6
SY89824LHZ IC CLOCK BUFFER MUX 2:22 64-TQFP
SY89823LHY IC CLK BUF MUX TRNSL 2:22 64TQFP
相關代理商/技術參數
參數描述
SY89467UHY TR 功能描述:編碼器、解碼器、復用器和解復用器 1:20 LVPECL Fanout w/ 2:1 FSI Input MUX RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量(輸入/輸出):2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray
SY89468U 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Precision LVDS 1:20 Fanout with 2:1 MUX and Internal Termination with Fail-Safe Input
SY89468UHY 功能描述:編碼器、解碼器、復用器和解復用器 1:20 LVDS Fanout w/ 2:1 FSI Input MUX RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量(輸入/輸出):2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray
SY89468UHY TR 功能描述:編碼器、解碼器、復用器和解復用器 1:20 LVDS Fanout w/ 2:1 FSI Input MUX RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量(輸入/輸出):2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray
SY89468UHYTR 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Precision LVDS 1:20 Fanout with 2:1 MUX and Internal Termination with Fail-Safe Input