- 您現在的位置：買賣IC網 > PDF目錄385893 > SY88713VKC (MICREL INC) 3.3V/5V 622 Mbps PECL LOW-POWER LIMITING POST AMPLIFIER W/PECL SIGNAL DETECT PDF資料下載
參數資料
| 型號： | SY88713VKC |
| 廠商： | MICREL INC |
| 元件分類： | 數字傳輸電路 |
| 英文描述： | 3.3V/5V 622 Mbps PECL LOW-POWER LIMITING POST AMPLIFIER W/PECL SIGNAL DETECT |
| 中文描述： | ATM/SONET/SDH SUPPORT CIRCUIT, PDSO10 |
| 封裝： | 3 MM, MSOP-10 |
| 文件頁數： | 5/8頁 |
| 文件大?。?/td> | 55K |
| 代理商： | SY88713VKC |
5
SY88713V
Micrel, Inc.
M9999-072505
hbwhelp@micrel.com or (408) 955-1690
DETAILED DESCRIPTION
The SY88713V low-power limiting post amplifier operates
from a single +3.3V or +5V power supply, over temperatures
from
–
40
°
C to +85
°
C. Signals with data rates up to 622Mbps
and as small as 5mVp-p can be amplified. Figure 1 shows
the allowed input voltage swing. The SY88713V generates
an SD output. SD
LVL
sets the sensitivity of the input
amplitude detection.
Input Amplifier/Buffer
Figure 2 shows a simplified schematic of the SY88713V's
input stage. The high sensitivity of the input amplifier allows
signals as small as 5mVp-p to be detected and amplified.
The input amplifier allows input signals as large as
1800mVp-p. Input signals are linearly amplified with a
typically 38dB differential voltage gain. Since it is a limiting
amplifier, the SY88713V outputs typically 1500mVp-p
voltage-limited waveforms for input signals that are greater
than 18mVp-p. Applications requiring the SY88713V to
operate with high-gain should have the upstream TIA placed
as close as possible to the SY88713V
’
s input pins to ensure
the best performance of the device.
Output Buffer
The SY88713V
’
s PECL output buffer is designed to drive
50
lines. The output buffer requires appropriate termination
for proper operation. An external 50
resistor to V
CC
–
2V
for each output pin provides this. Figure 3 shows a simplified
schematic of the output stage and includes an appropriate
termination method.
Signal-Detect
The SY88813V generates a chatter-free PECL signal-
detect (SD) similar to the SY88713V's output buffer. SD is
used to determine that the input amplitude is large enough
to be considered a valid input. SD asserts high if the input
amplitude rises above the threshold set by SD
LVL
and
deasserts low otherwise. /EN deasserts the true output signal
without removing the input signals. Typically 4.6dB SD
hysteresis is provided to prevent chattering.
Signal-Detect Level Set
A programmable signal-detect level set pin (SD
LVL
) sets
the threshold of the input amplitude detection. Setting a
voltage on SD
LVL
between V
CC
and V
REF
sets this threshold.
If desired, a resistor divider between V
CC
and V
REF
, as
shown in Figure 4, also creates this threshold. The smaller
the voltage difference from SD
LVL
to V
CC
, the smaller the
SD sensitivity. Hence, larger input amplitude is required to
assert SD.
“
Typical Operating Characteristics
”
shows the
relationship between the input amplitude detection sensitivity
and the SD
LVL
voltage.
Hysteresis
The SY88713V provides typically 4.6dB SD electrical
hysteresis. By definition, a power ratio measured in dB is
10log(power ratio). Power is calculated as V
2IN
/R for an
electrical signal. Hence the same ratio can be stated as
20log(voltage ratio). While in linear mode, the electrical
voltage input changes linearly with the optical power and
hence the ratios change linearly. Therefore, the optical
hysteresis in dB is half the electrical hysteresis in dB given
in the datasheet. The SY88713V provides typically 2.3dB
SD optical hysteresis. As the SY88713V is an electrical
device, this datasheet refers to hysteresis in electrical terms.
With 6dB SD hysteresis, a voltage factor of two is required
to assert or deassert SD.
相關PDF資料 |
PDF描述 |
|---|---|
| SY88713VKCTR | 3.3V/5V 622 Mbps PECL LOW-POWER LIMITING POST AMPLIFIER W/PECL SIGNAL DETECT |
| SY88713VKG | 3.3V/5V 622 Mbps PECL LOW-POWER LIMITING POST AMPLIFIER W/PECL SIGNAL DETECT |
| SY88713VKGYR | 3.3V/5V 622 Mbps PECL LOW-POWER LIMITING POST AMPLIFIER W/PECL SIGNAL DETECT |
| SY88782L | 3.3V, 1.25 Gbps HIgh Current, Low Power Laser Driver for Datacom Telecom Applications |
| SY88782LMG | 3.3V, 1.25 Gbps HIgh Current, Low Power Laser Driver for Datacom Telecom Applications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SY88713VKC TR | 功能描述:IC AMP POST PECL 3.3V/5V 10-MSOP RoHS:否 類別:集成電路 (IC) >> 線性 - 放大器 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:可變增益放大器 應用:CATV 安裝類型:表面貼裝 封裝/外殼:20-WQFN 裸露焊盤 供應商設備封裝:20-TQFN-EP（5x5） 包裝:托盤 |
| SY88713VKCTR | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:3.3V/5V 622 Mbps PECL LOW-POWER LIMITING POST AMPLIFIER W/PECL SIGNAL DETECT |
| SY88713VKG | 功能描述:限幅放大器 3.3V/5V 622Mbps PECL Low Power Limiting Post Amplifier W/ PECL SD (I Temp, Green) RoHS:否 制造商:Micrel 輸入電壓范圍（最大值）:3.6 V 工作電源電壓:3.3 V 電源電流:40 mA 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:MSOP-10 封裝:Tube |
| SY88713VKG TR | 功能描述:限幅放大器 3.3V/5V 622Mbps PECL Low Power Limiting Post Amplifier W/ PECL SD (I Temp, Green) RoHS:否 制造商:Micrel 輸入電壓范圍（最大值）:3.6 V 工作電源電壓:3.3 V 電源電流:40 mA 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:MSOP-10 封裝:Tube |
| SY88713VKGYR | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:3.3V/5V 622 Mbps PECL LOW-POWER LIMITING POST AMPLIFIER W/PECL SIGNAL DETECT |
發布緊急采購，3分鐘左右您將得到回復。