參數資料
型號： STLED316SMTR
廠商： STMICROELECTRONICS
元件分類： 顯示控制器
英文描述： 4 X 17 SEGMENTS SEGMENT LED DRVR AND DSPL CTLR, PDSO24
封裝： ROHS COMPLIANT, SOP-24
文件頁數： 2/33頁
文件大小： 438K
代理商： STLED316SMTR
STLED316S functional description
STLED316S
10/33
3
STLED316S functional description
The STLED316S is a common-anode LED driver controller which can be used to drive red,
green or blue LEDs as the current is adjustable through the external resistor. In the common
anode configuration, the segment outputs sink the current from the cathodes while the digit
outputs source the current to the anodes. The configurable output current can be used to
drive LEDs with different current ratings (red, green or blue). The brightness of the whole
display can be controlled through the serial interface as described later. The outputs can be
connected together in parallel to drive a single LED. In this case, two parallel current
sources of equal value drive a single LED. The external resistor value can be set accordingly
to determine the desired output current thus controlling the display brightness.
Soft-start limits the inrush current during power-up. The display is blanked (LEDs are turned
off or in high-Z state) on power-up.
3.1
Low power mode of operation
Upon initial power up or when not configured or when not used, the STLED316S will be in
low power mode of operation wherein the current consumption drops to less than 1mA.
During this mode, the data configured is maintained as long as the supply voltage is still
present (the contents of the internal RAM need the supply voltage to be present). Port
configuration and output levels are restored when the STLED316S resumes normal
operation. For minimum supply current in shutdown mode, logic inputs should be at GND or
VCC.
3.2
Serial interface
The interface is used to write configuration and display data to the STLED316S. The serial
interface comprises of a shift register into which DIN is clocked on the rising edge of the
CLK when STB is low. When STB is low, falling transitions on CLK clock the data from the
device to the microcontroller. The 8-bit data is decoded to determine and execute the
command.
STB indicates to the device the start of communication when it goes low. DIN/DOUT pin is
bi-directional. The data will be validated during positive pulse of the clock in both write/read
modes. If the STB signal goes high before completing the data byte write to the device, the
preceding data bits are ignored and the previous configuration remains intact.
3.3
Initial power up
On initial power-up, all control registers are reset, the display is blanked and the
STLED316S is in the low power mode. All the outputs are in high-impedance state at initial
power-up. The DIN/DOUT is pulled high by an external pull-up resistor. The display driver
has to be configured before the display can be used.
相關PDF資料
PDF描述
STM32F101C8T6 32-BIT, FLASH, 36 MHz, RISC MICROCONTROLLER, PQFP48
STM32F101R6T6 32-BIT, FLASH, 36 MHz, RISC MICROCONTROLLER, PQFP64
STM32F101VBT6 32-BIT, FLASH, 36 MHz, RISC MICROCONTROLLER, PQFP100
STM32F101T6U6 32-BIT, FLASH, 36 MHz, RISC MICROCONTROLLER, QCC36
STM32F101CBT6AXX 32-BIT, FLASH, 36 MHz, RISC MICROCONTROLLER, PQFP48
相關代理商/技術參數
參數描述
STLED325QTR 功能描述:LED照明驅動器 I2C interfaced LED controller/driver RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N
STLED32MAT-EVAL1 功能描述:BOARD EVALUATION FOR LED ARRAY RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP
STLED524 功能描述:IC MATRIX LED DISPL DVR 56CSP 制造商:stmicroelectronics 系列:- 包裝:剪切帶（CT） 零件狀態:有效 顯示類型:LED 配置:點陣 接口:SPI 數字或字符:- 電流 - 電源:- 電壓 - 電源:2.7 V ~ 5.5 V 工作溫度:-30°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:56-UFBGA，WLCSP 供應商器件封裝:56-CSP（3.4x3.0） 標準包裝:1
ST-LEQ1 制造商:Radio Design Labs 功能描述:Use With Vca Loudne Equalizer 制造商:RADIO DESIGN LABS 功能描述:LOUDNESS EQUALIZER USE WITH VCA
STLGCA-1.024 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Crystal Oscillator
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*