- 您現在的位置：買賣IC網 > PDF目錄382554 > ST90158 (意法半導體) 8/16-BIT MCU FAMILY WITH UP TO 64K ROM/OTP/EPROM AND UP TO 2K RAM PDF資料下載
參數資料
| 型號： | ST90158 |
| 廠商： | 意法半導體 |
| 英文描述： | 8/16-BIT MCU FAMILY WITH UP TO 64K ROM/OTP/EPROM AND UP TO 2K RAM |
| 中文描述： | 微控制器16位產品的家庭多達64K的ROM /檢察官/ EPROM和2K的內存 |
| 文件頁數： | 95/190頁 |
| 文件大?。?/td> | 1152K |
| 代理商： | ST90158 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁當前第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁
95/190
ST90158 - I/O PORTS
8.5 ALTERNATE FUNCTION ARCHITECTURE
Each I/O pin may be connected to three different
types of internal signal:
– Data bus Input/Output
– Alternate Function Input
– Alternate Function Output
8.5.1 Pin Declared as I/O
A pin declared as I/O, is connected to the I/O buff-
er. This pin may be an Input, an Output, or a bidi-
rectional I/O, depending on the value stored in
(PxC2, PxC1 and PxC0).
8.5.2 Pin Declared as an Alternate Input
A single pin may be directly connected to several
Alternate inputs. In this case, the user must select
the required input mode (with the PxC2, PxC1,
PxC0 bits) and enable the selected Alternate
Function in the Control Register of the peripheral.
No specificport configuration is required toenable
an Alternate Function input, since the input buffer
is directly connected to each alternate function
module on the shared pin. As more than one mod-
ule canuse the sameinput, it is up to the user soft-
ware to enable the required moduleas necessary.
Parallel I/Os remain operational even when using
an Alternate Function input. The exception to this
is when an I/O port bit is permanently assigned by
hardware as an A/D bit. In this case , after soft-
ware programmingof the bit inAF-OD-TTL, the Al-
ternate function output is forced to logic level 1.
The analog voltage level on the corresponding pin
is directly input to the A/D.
8.5.3 Pin Declared as an Alternate Function
Output
The user must select the AF OUT configuration
using the PxC2, PxC1, PxC0 bits. Several Alter-
nate Functionoutputs may drive a common pin. In
such case, the Alternate Function output signals
are logically ANDed before driving the common
pin. The user must therefore enable the required
Alternate Function Output by software.
WARNING
: Whena pin isconnected both to an al-
ternate functionoutput and to an alternate function
input, it should be noted that the output signal will
always be present on the alternate function input.
8.6 I/O STATUS AFTER WFI, HALT AND RESET
The status of the I/O ports during the Wait For In-
terrupt, Halt and Reset operational modes is
shown in thefollowing table. The External Memory
Interface ports are shown separately. If only the in-
ternal memory is being used and theports are act-
ing as I/O, the status is thesame as shown for the
other I/O ports.
Mode
Ext. Mem - I/O Ports
P0
High Imped-
ance ornext
address (de-
pending on
the last
memory op-
eration per-
formed on
Port)
High Imped-
ance
I/O Ports
P1, P2, P6
WFI
Next
Address
Not Affected (clock
outputs running)
HALT
Next
Address
Not Affected (clock
outputs stopped)
Bidirectional Weak
Pull-up (High im-
pedance when disa-
bled in hardware).
RESET
Alternate function push-
pull (ROMless device)
9
相關PDF資料 |
PDF描述 |
|---|---|
| ST90158-ST90135 | 8/16-BIT MCU FAMILY WITH UP TO 64K ROM/OTP/EPROM AND UP TO 2K RAM |
| ST90158M7Q6 | 8/16-BIT MCU FAMILY WITH UP TO 64K ROM/OTP/EPROM AND UP TO 2K RAM |
| ST90158M9Q6 | 8/16-BIT MCU FAMILY WITH UP TO 64K ROM/OTP/EPROM AND UP TO 2K RAM |
| ST90158M9T1 | 8/16-BIT MCU FAMILY WITH UP TO 64K ROM/OTP/EPROM AND UP TO 2K RAM |
| ST90E158 | 8/16-BIT MCU FAMILY WITH UP TO 64K ROM/OTP/EPROM AND UP TO 2K RAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST90158-EMU2B | 功能描述:仿真器/模擬器 ST9 Emulator Board RoHS:否 制造商:Blackhawk 產品:System Trace Emulators 工具用于評估:C6000, C5000, C2000, OMAP, DAVINCI, SITARA, TMS470, TMS570, ARM 7/9, ARM Cortex A8/R4/M3 用于:XDS560v2 |
| ST90158M7 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8/16-BIT MICROCONTROLLER (MCU) WITH 16 TO 64K ROM. OTP OR EPROM. 512 TO 2K RAM - ST9 + FAMILY |
| ST90158M7LVT6 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8/16-BIT MICROCONTROLLER (MCU) WITH 16 TO 64K ROM. OTP OR EPROM. 512 TO 2K RAM - ST9 + FAMILY |
| ST90158M7Q6 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8/16-BIT MCU FAMILY WITH UP TO 64K ROM/OTP/EPROM AND UP TO 2K RAM |
| ST90158M7T6 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。