- 您現在的位置：買賣IC網 > PDF目錄382553 > ST7FLITE19F1B6 (意法半導體) 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, 4 TIMERS, SPI PDF資料下載
參數資料
| 型號： | ST7FLITE19F1B6 |
| 廠商： | 意法半導體 |
| 英文描述： | 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, 4 TIMERS, SPI |
| 中文描述： | 8位單電壓閃存存儲器，數據EEPROM，模數轉換器，4定時器，微控制器的SPI |
| 文件頁數： | 92/131頁 |
| 文件大小： | 2046K |
| 代理商： | ST7FLITE19F1B6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁當前第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁
ST7LITE1
92/131
1
13.2 ABSOLUTE MAXIMUM RATINGS
Stresses above those listed as “absolute maxi-
mum ratings” may cause permanent damage to
the device. This is a stress rating only and func-
tional operation of the device under these condi-
13.2.1 Voltage Characteristics
tions is not implied. Exposure to maximum rating
conditions for extended periods may affect device
reliability.
13.2.2 Current Characteristics
13.2.3 Thermal Characteristics
Notes:
1. Directly connecting the I/O pins to V
or V
could damage the device if an unexpected change of the I/O configura-
tion occurs (for example, due to a corrupted program counter). To guarantee safe operation, this connection has to be
done through a pull-up or pull-down resistor (typical: 10k
for I/Os). Unused I/O pins must be tied in the same way to V
DD
or V
SS
according to their reset configuration.
2. I
must never be exceeded. This is implicitly insured if V
IN
maximum is respected. If V
maximum cannot be
respected, the injection current must be limited externally to the I
value. A positive injection is induced by V
>V
while a negative injection is induced by V
<V
. For true open-drain pads, there is no positive injection current, and the
corresponding V
IN
maximum must always be respected
3. All power (V
DD
) and ground (V
SS
) lines must always be connected to the external supply.
4. Negative injection disturbs the analog performance of the device. In particular, it induces leakage currents throughout
the device including the analog inputs. To avoid undesirable effects on the analog functions, care must be taken:
- Analog input pins must have a negative injection less than 0.8 mA (assuming that the impedance of the analog voltage
is lower than the specified limits)
- Pure digital pins must have a negative injection less than 1.6mA. In addition, it is recommended to inject the current as
far as possible from the analog input pins.
5. No negative current injection allowed on PB0 and PB1 pins.
6. When several inputs are submitted to a current injection, the maximum
Σ
I
is the absolute sum of the positive
and negative injected currents (instantaneous values). These results are based on characterisation with
Σ
I
INJ(PIN)
maxi-
mum current injection on four I/O port pins of the device.
Symbol
Ratings
Maximum value
Unit
V
DD
- V
SS
V
IN
Supply voltage
Input voltage on any pin
1) & 2)
7.0
V
V
SS
-0.3 to V
DD
+0.3
see
section 13.7.3 on
page 104
V
ESD(HBM)
Electrostatic discharge voltage (Human Body Model)
V
Symbol
Ratings
Maximum value
Unit
I
VDD
I
VSS
Total current into V
DD
power lines (source)
3)
Total current out of V
SS
ground lines (sink)
3)
Output current sunk by any standard I/O and control pin
Output current sunk by any high sink I/O pin
Output current source by any I/Os and control pin
Injected current on RESET pin
Injected current on OSC1 and OSC2 pins
Injected current on PB0 and PB1 pins
5)
Injected current on any other pin
6)
Total injected current (sum of all I/O and control pins)
6)
100
100
25
50
- 25
± 5
± 5
+5
± 5
± 20
mA
I
IO
I
INJ(PIN) 2) & 4)
Σ
I
INJ(PIN) 2)
Symbol
Ratings
Value
Unit
T
STG
Storage temperature range
Maximum junction temperature (see Table 21, “THERMAL CHARACTERISTICS,” on
page 119)
-65 to +150
°C
T
J
相關PDF資料 |
PDF描述 |
|---|---|
| ST7PLITE10F1B6 | 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, 4 TIMERS, SPI |
| ST7PLITE15F1B6 | 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, 4 TIMERS, SPI |
| ST7PLITE19F1B6 | 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, 4 TIMERS, SPI |
| ST7FLITE10 | 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, 4 TIMERS, SPI |
| ST7FLITE10F1M6 | 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, 4 TIMERS, SPI |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST7FLITE19F1B6 | 制造商:STMicroelectronics 功能描述:IC 8BIT FLASH MCU 7FLITE19 DIP20 |
| ST7FLITE19F1M6 | 功能描述:8位微控制器 -MCU Flash 4K SPI RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| ST7FLITE20F1B6 | 功能描述:8位微控制器 -MCU 8 BITS MICROCONTR RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| ST7FLITE20F2B6 | 功能描述:8位微控制器 -MCU Flash 8K SPI 384 RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| ST7FLITE20F2B6 | 制造商:STMicroelectronics 功能描述:IC 8BIT FLASH MCU 7FLITE20 DIP20 |
發布緊急采購，3分鐘左右您將得到回復。