參數資料
型號: ST6265BN6
廠商: 意法半導體
英文描述: 8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, SAFE RESET, AUTO-RELOAD TIMER, EEPROM AND SPI
中文描述: 8位檢察官辦公室/存儲器與阿微控制器/ D轉換器,安全復位,自動重加載定時器,EEPROM和的SPI
文件頁數: 23/74頁
文件大小: 538K
代理商: ST6265BN6
23/74
ST62T55B ST62T65B/E65B
3.3 DIGITAL WATCHDOG
The digital Watchdog consists of a reloadable
downcounter timer which can be used to provide
controlled recovery from software upsets.
The Watchdog circuit generates a Reset when the
downcounter reaches zero. User software can
prevent this reset by reloading the counter, and
should therefore be written so that the counter is
regularly reloaded while the user program runs
correctly. In the event of a software mishap (usual-
ly caused by externally generated interference),
the user program will no longer behave in its usual
fashion and the timer register will thus not be re-
loaded periodically. Consequently the timer will
decrement down to 00h and reset the MCU. In or-
der to maximise the effectiveness of the Watchdog
function, user software must be written with this
concept in mind.
Watchdog behaviour is governed by two options,
known
as
“WATCHDOG
HARDWARE or SOFTWARE) and “EXTERNAL
STOP MODE CONTROL” (seeTable 7).
In the SOFTWARE option, the Watchdog is disa-
bled until bit C of the DWDR register has been set.
ACTIVATION”
(i.e.
When the Watchdog is disabled, low power Stop
mode is available. Once activated, the Watchdog
cannot be disabled, except by resetting the MCU.
In the HARDWARE option, the Watchdog is per-
manently enabled. Since the oscillator will run con-
tinuously, low power mode is not available. The
STOP instruction is interpreted as a WAIT instruc-
tion, and the Watchdog continues to countdown.
However, when the EXTERNAL STOP MODE
CONTROL option has been selected low power
consumption may be achieved in Stop Mode.
Execution of the STOP instruction is then gov-
erned by a secondary function associated with the
NMI pin. If a STOP instruction is encountered
when the NMI pin is low, it is interpreted as WAIT,
as described above. If, however, the STOP in-
struction is encountered when the NMI pin is high,
the Watchdog counter is frozen and the CPU en-
ters STOP mode.
When the MCU exits STOP mode (i.e. when an in-
terrupt is generated), the Watchdog resumes its
activity.
Table 7. Recommended Option Choices
FunctionsRequired
Stop Mode & Watchdog
Stop Mode
Watchdog
Recommended Options
“EXTERNAL STOP MODE” & “HARDWARE WATCHDOG”
“SOFTWARE WATCHDOG”
“HARDWARE WATCHDOG”
23
相關PDF資料
PDF描述
st62E18C 8-Bit MCUs with A/D Converter, Auto-Reload Timer, UART, OSG, Safe Reset and 20-Pin Package(8位微控制器(8M))
ST62T60CM6 IC-SM-8-BIT MCU 4K OTP
ST62T60C 8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, SAFE RESET, AUTO-RELOAD TIMER, EEPROM AND SPI
ST62T63C 8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, SAFE RESET, AUTO-RELOAD TIMER, EEPROM AND SPI
ST63E69 8-Bit EPROM HCMOS MCUs For Digital Controlled Multi Frequency Monitor(應用于數字控制的多頻顯示器的8位EPROM HCMOS微控制器)
相關代理商/技術參數
參數描述
ST6265BN6/XXX 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, SAFE RESET, AUTO-RELOAD TIMER, EEPROM AND SPI
ST6265C 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT MICROCONTROLLER ( MCU ) WITH OTP. ROM. FASTROM. EPROM. A/D CONVERTER. SAFE RESET. AUTO-RELOAD TIMER. EEPROM AND SPI
ST626X 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8/16-Bit Micros
ST626XC-KIT 制造商:STMicroelectronics 功能描述:ST625X, 6X KIT - Bulk
ST626XC-KIT/EU 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:DEVELOPMENT KIT ST626 EURO