參數資料
型號： ST6263BM1
廠商： 意法半導體
英文描述： DIODE ZENER SINGLE 200mW 15Vz 5mA-Izt 0.0218 0.1uA-Ir 11 SOD-323 3K/REEL
中文描述： 8位檢察官辦公室/存儲器與阿微控制器/ D轉換器，自動重加載定時器，EEPROM和的SPI
文件頁數： 23/75頁
文件大?。?/td> 540K
代理商： ST6263BM1
23/75
ST62T53B/T60B/T63B ST62E60B
3.3 DIGITAL WATCHDOG
The digital Watchdog consists of a reloadable
downcounter timer which can be used to provide
controlled recovery from software upsets.
The Watchdog circuit generates a Reset when the
downcounter reaches zero. User software can
prevent this reset by reloading the counter, and
should therefore be written so that the counter is
regularly reloaded while the user program runs
correctly. In the event of a software mishap (usual-
ly caused by externally generated interference),
the user program will no longer behave in its usual
fashion and the timer register will thus not be re-
loaded periodically. Consequently the timer will
decrement down to 00h and reset the MCU. In or-
der to maximise the effectiveness of the Watchdog
function, user software must be written with this
concept in mind.
Watchdog behaviour is governed by two options,
known
as
“WATCHDOG
HARDWARE or SOFTWARE) and “EXTERNAL
STOP MODE CONTROL” (seeTable 8).
In the SOFTWARE option, the Watchdog is disa-
bled until bit C of the DWDR register has been set.
ACTIVATION”
(i.e.
When the Watchdog is disabled, low power Stop
mode is available. Once activated, the Watchdog
cannot be disabled, except by resetting the MCU.
In the HARDWARE option, the Watchdog is per-
manently enabled. Since the oscillator will run con-
tinuously, low power mode is not available. The
STOP instruction is interpreted as a WAIT instruc-
tion, and the Watchdog continues to countdown.
However, when the EXTERNAL STOP MODE
CONTROL option has been selected low power
consumption may be achieved in Stop Mode.
Execution of the STOP instruction is then gov-
erned by a secondary function associated with the
NMI pin. If a STOP instruction is encountered
when the NMI pin is low, it is interpreted as WAIT,
as described above. If, however, the STOP in-
struction is encountered when the NMI pin is high,
the Watchdog counter is frozen and the CPU en-
ters STOP mode.
When the MCU exits STOP mode (i.e. when an in-
terrupt is generated), the Watchdog resumes its
activity.
Table 8. Recommended Option Choices
FunctionsRequired
Stop Mode & Watchdog
Stop Mode
Watchdog
Recommended Options
“EXTERNAL STOP MODE” & “HARDWARE WATCHDOG”
“SOFTWARE WATCHDOG”
“HARDWARE WATCHDOG”
23
相關PDF資料
PDF描述
ST6253CB1 8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, SAFE RESET, AUTO-RELOAD TIMER, EEPROM AND SPI
ST6265BM3 Replaced by PT78HT205 : 5Vout 2A Wide Input Positive Step-Down ISR 3-SIP MODULE -40 to 85
ST6265BM6 Replaced by PT78HT205 : 5Vout 2A Wide Input Positive Step-Down ISR 3-SIP MODULE -40 to 85
ST6265BB1 8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, AUTO-RELOAD TIMER, EEPROM AND SPI
ST6265BB3 8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, AUTO-RELOAD TIMER, EEPROM AND SPI
相關代理商/技術參數
參數描述
ST6263BM1/XXX 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, SAFE RESET, AUTO-RELOAD TIMER, EEPROM AND SPI
ST6263BM3 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, SAFE RESET, AUTO-RELOAD TIMER, EEPROM AND SPI
ST6263BM3/XXX 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, SAFE RESET, AUTO-RELOAD TIMER, EEPROM AND SPI
ST6263BM6 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, SAFE RESET, AUTO-RELOAD TIMER, EEPROM AND SPI
ST6263BM6/XXX 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, SAFE RESET, AUTO-RELOAD TIMER, EEPROM AND SPI
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*