- 您現在的位置：買賣IC網 > PDF目錄382551 > ST623x-EMU2 (意法半導體) Real Time Emulation Development Tools for ST6218/ST6228/ST623x MCUs(ST6218/6228/623x的實時開發工具) PDF資料下載
參數資料
| 型號： | ST623x-EMU2 |
| 廠商： | 意法半導體 |
| 英文描述： | Real Time Emulation Development Tools for ST6218/ST6228/ST623x MCUs(ST6218/6228/623x的實時開發工具) |
| 中文描述： | 實時仿真開發工具ST6218/ST6228/ST623x微控制器（ST6218/6228/623x的實時開發工具） |
| 文件頁數： | 6/20頁 |
| 文件大小： | 236K |
| 代理商： | ST623X-EMU2 |
6/20
ST623x-EMU2 - ST6 HDS2 NEW MAINFRAME EMULATOR
2.1 MAIN BOARD
The Main board controls the emulator thanks to a
ST9 central processing unit which executes com-
mands coming from host computer through the
parallel line.
The board contains all emulation resources, the
core of the ST6, the Program ROM emulation, the
break point logic, the trace memory, the automa-
ton and all necessary logic for a real time emula-
tion.
Two connectors, J1 and J2, are used to exchange
signals with the dedication board.
The amount of program memory in the main board
is factory set at 32k, in fact the size of the memory
depends on the dedication board, which contains
the Program Rom Pagination Register (PRPR) if it
exists (no PRPR for memory size lower than 4k).
No configuration jumpers are required.
2.2 ST6 HDS2 MAIN BOARD
On the rear panel there is:
– a power plug to connect power: 5 Volts 3 Amp
min. (The delivered power is 100 volts to 240
volts input and 5 Amp output).
– a power switch.
– a parallel connector for an IBM PC(TM) compat-
ible.
On front panel:
– a led “POWER ON” signal.
– OUT 1 and OUT 2 signals which can be used for
synchronizing an external equipment.
– 2 leds indicating when the ST6 core is in“STOP”
or “WAIT” mode.
– a 16 pin connector for data acquisition signals.
The explanation of these signals is done in the
debugger manual.
2.2.1 External output: OUT1 and OUT2
For debugging hardware it is very useful to have
synchronization signals. The goal of the outputs 1
and 2 is to offer this feature to the user. They can
be programmed differently whether the debugger
used is the DOS debugger ST6NDB or the Source
Level Debugger WGDB6, as explained in the two
following paragraph. They are full programmable
with WGDB6.
Output OUT1 and OUT2 under ST6NDB
When
using old DOS Version of debugger
ST6NDB:
This feature is programmable thanks to Hardware
Breakpoint Menu. The breakpoint MENU allows to
define breaking events. These events will gener-
ate an actual breakpoint only if break enable is
ON. When break is off, these events are existing in
the development tool. In the HDS2 emulator ver-
sion up to 4.3, the signals OUT1 and OUT2 are
connected to these internal breaking events.
Therefore these signals can be used to synchro-
nize an external device while running (breakpoint
off).
Output OUT1 and OUT2 under WGDB6
When using WGDB6 new Version of debugger at
source level under WindowsTM:
This feature is full programmable thanks to Hard-
ware Events/Trigger Menu. Output OUT1 and
OUT2 can be programmed in two ways:
– Events for synchronisation: it allows to the user
to preset pulses synchronisation for an external
equipment. The events can be defined by ad-
dresses or by range of addresses.
– Events for Timing Measure: it allows to the user
to measure time elapsed during a subroutine for
example. In this case, output OUT2 is SET on a
user defined address, and RESET on an other
one, OUT1 is the ST6 clock cycle gated by
OUT2.
These 2 functioning modes are clearly displayed
on screen.
6
相關PDF資料 |
PDF描述 |
|---|---|
| ST6245BQ1 | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| ST62T45B | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| ST6245BQ6 | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| ST6263BB6 | 8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, AUTO-RELOAD TIMER, EEPROM AND SPI |
| ST6260BM1 | 8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, AUTO-RELOAD TIMER, EEPROM AND SPI |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST623X-KIT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:STARTER KIT DATASHEET FOR ST6230 |
| ST623X-KIT/110 | 功能描述:開發板和工具包 - 其他處理器 ST623X Starter Kit RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓: |
| ST623X-KIT/220 | 制造商:STMicroelectronics 功能描述:ST Development Kit, Including ST623X Starter Kit, Development Software CD-ROM, Parallel Cable, Power Supply, Window Development Devices ST62E30BF1, ST (More...) |
| ST623X-KIT/UK | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:STARTER KIT AB 8K BYTE |
| ST-6-24 | 功能描述:XFRMR PWR 115V 12VAC 1.6A RoHS:是 類別:變壓器 >> 功率 系列:ST 標準包裝:1 系列:260 類型:標準 最大功率:65 VA 主線圈:雙 副線圈:三路，中心抽頭 在某電流時的串聯輸出電壓:500 VAC @ 85mA，5 VAC @ 2A，6.3 VAC @ 2A 在某電流時的并聯輸出電壓:- 安裝類型:底座安裝 尺寸/尺寸:102.36mm L x 67.31mm W 高度 - 座高（最大）:66.80mm 端接類型:導線引線 |
發布緊急采購，3分鐘左右您將得到回復。