REV. 5.0.2 28 FCR[1]: RX FIFO Reset This bit is only active when FCR bit-0 is a ‘1’." />
參數資料
型號： ST16C654DIQ64-F
廠商： Exar Corporation
文件頁數： 21/51頁
文件大小： 0K
描述： IC UART FIFO 64B QUAD 64LQFP
標準包裝： 160
特點： *
通道數： 4，QUART
FIFO's： 64 字節
規程： RS232
電源電壓： 2.97 V ~ 5.5 V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 64-LQFP
供應商設備封裝： 64-LQFP（10x10）
包裝： 托盤
其它名稱： 1016-1271
ST16C654/654D
xr
2.97V TO 5.5V QUAD UART WITH 64-BYTE FIFO
REV. 5.0.2
28
FCR[1]: RX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No receive FIFO reset (default)
Logic 1 = Reset the receive FIFO pointers and FIFO level counter logic (the receive shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[2]: TX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No transmit FIFO reset (default).
Logic 1 = Reset the transmit FIFO pointers and FIFO level counter logic (the transmit shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[3]: DMA Mode Select
Controls the behavior of the -TXRDY and -RXRDY pins. See DMA operation section for details.
Logic 0 = Normal Operation (default).
Logic 1 = DMA Mode.
FCR[5:4]: Transmit FIFO Trigger Select
(logic 0 = default, TX trigger level = one)
These 2 bits set the trigger level for the transmit FIFO. The UART will issue a transmit interrupt when the
number of characters in the FIFO falls below the selected trigger level, or when it gets empty in case that the
FIFO did not get filled over the trigger level on last re-load. Table 12 below shows the selections. EFR bit-4
must be set to ‘1’ before these bits can be accessed. Note that the receiver and the transmitter cannot use
different trigger tables. Whichever selection is made last applies to both the RX and TX side.
FCR[7:6]: Receive FIFO Trigger Select
(logic 0 = default, RX trigger level =1)
These 2 bits are used to set the trigger level for the receive FIFO. The UART will issue a receive interrupt when
the number of the characters in the FIFO crosses the trigger level. Table 12 shows the complete selections.
TABLE 12: TRANSMIT AND RECEIVE FIFO TRIGGER LEVEL SELECTION
FCR
BIT-7
FCR
BIT-6
FCR
BIT-5
FCR
BIT
-4
RECEIVE
TRIGGER
LEVEL
TRANSMIT
TRIGGER
LEVEL
0
1
0
1
0
1
0
1
0
1
0
1
8
16
56
60
8
16
32
56
相關PDF資料
PDF描述
ST78C34CJ44-F IC UART FIFO 83B 44PLCC
ST78C36ACJ44-F IC UART FIFO 16B 44PLCC
SW06GSZ-REEL IC SWITCH QUAD SPST 16SOIC
SX1501I087TRT IC GPIO EXPANDER I2C 4CH 20QFN
SX1504I087TRT IC GPIO EXPANDER I2C 4CH 20QFN
相關代理商/技術參數
參數描述
ST16C654IJ68 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:
ST16C654IJ68-F 功能描述:UART 接口集成電路 QUAD UARTW/64BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
ST16C654IJ68-F 制造商:Exar Corporation 功能描述:IC QUAD UART 1.5MBPS 5.5V 68-PLCC
ST16C654IJ68TR-F 制造商:Exar Corporation 功能描述:UART 4-CH 64Byte FIFO 3.3V/5V 68-Pin PLCC T/R 制造商:Exar Corporation 功能描述:2.97V to 5.5V Quad UART with 64 Byte FIFOs PLCC 68 制造商:Exar Corporation 功能描述:ST16C654IJ68TR-F
ST16C654IQ 制造商:Exar Corporation 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*