- 您現在的位置：買賣IC網 > PDF目錄384931 > ST16C650AIQ48 (EXAR CORP) 2.90V TO 5.5V UART WITH 32-BYTE FIFO PDF資料下載
參數資料
| 型號： | ST16C650AIQ48 |
| 廠商： | EXAR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 2.90V TO 5.5V UART WITH 32-BYTE FIFO |
| 中文描述： | 1 CHANNEL(S), 3.125M bps, SERIAL COMM CONTROLLER, PQFP48 |
| 封裝： | 7 X 7 MM, 1 MM HEIGHT, TQFP-48 |
| 文件頁數： | 35/53頁 |
| 文件大小： | 666K |
| 代理商： | ST16C650AIQ48 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁
á
REV. 5.0.0
ST16C650A
2.90V TO 5.5V UART WITH 32-BYTE FIFO
35
MSR[6]: RI Input Status
RI# (active high, logical 1). Normally this bit is the compliment of the RI# input. In the loopback mode this bit is
equivalent to bit-2 in the MCR register. The RI# input may be used as a general purpose input when the
modem interface is not used.
MSR[7]: CD Input Status
CD# (active high, logical 1). Normally this bit is the compliment of the CD# input. In the loopback mode this bit
is equivalent to bit-3 in the MCR register. The CD# input may be used as a general purpose input when the
modem interface is not used.
4.11
Infrared Transmit Pulse Width Control Register (IRPW) - Write Only
The IRPW register allows the user to program the encoder’s pulse width. This cuts the LED on-time, hence,
reducing power consumption.
IRPW [7:0]: Pulse width control
A 0x00 value (default) will set the pulse width to normal width of 3/16 of the data bit rate. The programmable
infrared pulse width can be calculated using the following equation:
Infrared pulse width (PW) = Crystal clock period x ‘N’, where ‘N’ is the value in IRPW from 1 to 255.
Examples:
Crystal frequency = 14.7456MHz (clock period of 67.82ns)
PW = 67.82 x ‘N’ or ranges from 67.82ns to 17.29ms
Caution: Never allow PW to exceed the operating data rate bit period, else the encoder stops.
4.12
Scratch Pad Register (SPR)
This is an 8-bit general purpose register for the user to store temporary data. The content of this register is
preserved during sleep mode but becomes 0xFF (default) after a reset or a power off-on cycle.
4.13
Baud Rate Generator Divisors (DLL and DLM) - Read/Write
The Baud Rate Generator (BRG) is a 16-bit counter that generates the data rate for the transmitter. The rate is
programmed through registers DLL and DLM which are only accessible when LCR bit-7 is set to ‘1’. See
Programmable Baud Rate Generator section for more details. The concatenation of the contents of DLM and
DLL gives the 16-bit divisor value which is used to calculate the baud rate:
Baud Rate = (Clock Frequency / 16) / Divisor
Also see MCR bit-7 and
Table 4
.
4.14
Device Identification Register (DVID) - Read Only
This register contains the device ID (0x04 for ST16C650A). Prior to reading this register, DLL and DLM should
be set to 0x00.
4.15
Device Revision Register (DREV) - Read Only
This register contains the device revision information. For example, 0x01 means revision A. Prior to reading
this register, DLL and DLM should be set to 0x00.
4.16
Enhanced Feature Register (EFR)
Enhanced features are enabled or disabled using this register. Bit 0-3 provide single or dual consecutive
character software flow control selection (see
Table 12
). When the Xon1 and Xon2 and Xoff1 and Xoff2 modes
are selected, the double 8-bit words are concatenated into two sequential characters. Caution: note that
whenever changing the TX or RX flow control bits, always reset all bits back to logic 0 (disable) before
programming a new setting.
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C650 | Voltage Regulator IC; Output Current Max:350mA; Supply Voltage Max:6V; Package/Case:8-TSSOP; Output Current:350mA; Output Voltage:3.3V; Current Rating:30.05A; Leaded Process Compatible:Yes; Output Voltage Max:3.3V RoHS Compliant: Yes |
| ST26C32CF16 | QUAD RS-422, RS-423 CMOS Differential Line Receiver |
| ST26C32 | MOSFET; Transistor Polarity:N Channel; Drain Source Voltage, Vds:20V; Continuous Drain Current, Id:13.4A; On-Resistance, Rds(on):0.0065ohm; Rds(on) Test Voltage, Vgs:4.5V; Package/Case:8-SOIC; Leaded Process Compatible:No |
| ST26C32CP16 | QUAD RS-422, RS-423 CMOS Differential Line Receiver |
| ST26C32IF16 | QUAD RS-422, RS-423 CMOS Differential Line Receiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C650AIQ48-F | 功能描述:UART 接口集成電路 UART W/32BYTEFIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C650AIQ48TR | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| ST16C650AIQ48TR-F | 功能描述:UART 接口集成電路 UART W/32BYTEFIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C650CJ44 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| ST16C650CJ44-F | 功能描述:UART 接口集成電路 UART W/32 BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。