參數資料
型號： ST16C650
廠商： Exar Corporation
英文描述： Voltage Regulator IC; Output Current Max:350mA; Supply Voltage Max:6V; Package/Case:8-TSSOP; Output Current:350mA; Output Voltage:3.3V; Current Rating:30.05A; Leaded Process Compatible:Yes; Output Voltage Max:3.3V RoHS Compliant: Yes
中文描述： 2.90V至5.5V UART的32字節FIFO
文件頁數： 33/53頁
文件大小： 666K
代理商： ST16C650
á
REV. 5.0.0
ST16C650A
2.90V TO 5.5V UART WITH 32-BYTE FIFO
33
LSR[5]: Transmit Holding Register Empty Flag
This bit is the Transmit Holding Register Empty indicator. The THR bit is set to a logic 1 when the last data byte
is transferred from the transmit holding register to the transmit shift register. The bit is reset to logic 0
concurrently with the data loading to the transmit holding register by the host. In the FIFO mode this bit is set
when the transmit FIFO is empty, it is cleared when the transmit FIFO contains at least 1 byte.
LSR[6]: Transmit Shift Register Empty Flag
This bit is the Transmit Shift Register Empty indicator. This bit is set to a logic 1 whenever the transmitter goes
idle. It is set to logic 0 whenever either the THR or TSR contains a data character. In the FIFO mode this bit is
set to one whenever the transmit FIFO and transmit shift register are both empty.
LSR[7]: Receive FIFO Data Error Flag
Logic 0 = No FIFO error (default).
Logic 1 = A global indicator for the sum of all error bits in the RX FIFO. At least one parity error, framing error
or break indication is in the FIFO data. This bit clears when there is no more error(s) in the FIFO.
4.9
Extra Feature Register (XFR) - Write Only
This register provides additional features and controls to the ST16C650A UART.
XFR [0]: Half-duplex Infrared Mode Enable
When infrared mode is enabled, MCR bit-6=1, this bit selects the infrared mode to operate in normal full-duplex
or half-duplex mode. This half-duplex mode feature is very desirable when the UART does not want to “see” its
own data that may be reflected.
Logic 0 = Disable. The receiver is active during data transmission.
Logic 1 = Enable half-duplex operation. The infrared receiver is disabled during data transmission.
XFR [1]: Invert Received Infrared Input Signal
This bit controls the input polarity of the infrared data.
Logic 0 = Infrared data input idles at logic 0 (default).
Logic 1 = Infrared data idles at logic 1, pulses low.
XFR [2]: Auto RS485 Enable
This bit enables the auto RS485 direction control feature for half-duplex operation with RS-485 transceiver.
The feature should only be enabled when normal RTS# output and auto RTS flow control are not used.
Logic 0 = Disable the auto RS485 direction control function. This allows normal RTS# output or auto RTS
flow control operation.
Logic 1 = Enable the auto RS485 direction function. The RTS# output will automatically change its logic state
to control the RS-485 transceiver from sending and receiving.
See “Auto RS485 Half-duplex Control” on
page 19.
XFR [3]: LSR Bad Data Interrupt Operation
When the LSR interrupt is enabled, IER bit-2=1, this bit selects when the interrupt pin (INT) will report received
character error: parity, framing or break. Use this feature only if application needs immediate knowledge when
a bad character is received.
Logic 0 = Received data error interrupt (LSR interrupt) will be generated when the bad character is available
for reading from the FIFO. This is compatible to industry standard 16C550 operation.
Logic 1 = Received data error interrupt (LSR interrupt) is generated immediately upon receipt of the bad
character. It will be reset when LSR is read. If user does not read the bad character out, another bad
character interrupt is generated when it’s available for reading from the FIFO.
相關PDF資料
PDF描述
ST26C32CF16 QUAD RS-422, RS-423 CMOS Differential Line Receiver
ST26C32 MOSFET; Transistor Polarity:N Channel; Drain Source Voltage, Vds:20V; Continuous Drain Current, Id:13.4A; On-Resistance, Rds(on):0.0065ohm; Rds(on) Test Voltage, Vgs:4.5V; Package/Case:8-SOIC; Leaded Process Compatible:No
ST26C32CP16 QUAD RS-422, RS-423 CMOS Differential Line Receiver
ST26C32IF16 QUAD RS-422, RS-423 CMOS Differential Line Receiver
ST26C32IP16 QUAD RS-422, RS-423 CMOS Differential Line Receiver
相關代理商/技術參數
參數描述
ST16C650A 制造商:EXAR 制造商全稱:EXAR 功能描述:2.90V TO 5.5V UART WITH 32-BYTE FIFO
ST16C650A_0508 制造商:EXAR 制造商全稱:EXAR 功能描述:2.90V TO 5.5V UART WITH 32-BYTE FIFO
ST16C650A_09 制造商:EXAR 制造商全稱:EXAR 功能描述:2.90V TO 5.5V UART WITH 32-BYTE FIFO
ST16C650ACJ44 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:
ST16C650ACJ44-F 功能描述:UART 接口集成電路 UART W/32BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*