- 您現在的位置：買賣IC網 > PDF目錄299932 > ST16C554DCJ68 (EXAR CORP) 4 CHANNEL(S), 1.5M bps, SERIAL COMM CONTROLLER, PQCC68 PDF資料下載
參數資料
| 型號： | ST16C554DCJ68 |
| 廠商： | EXAR CORP |
| 元件分類： | Serial IO/Communication Controller |
| 英文描述： | 4 CHANNEL(S), 1.5M bps, SERIAL COMM CONTROLLER, PQCC68 |
| 封裝： | PLASTIC, LCC-68 |
| 文件頁數： | 11/41頁 |
| 文件大?。?/td> | 582K |
| 代理商： | ST16C554DCJ68 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
ST16C554/554D
19
REV. 4.0.1
2.97V TO 5.5V QUAD UART WITH 16-BYTE FIFO
4.5
FIFO Control Register (FCR) - Write-Only
This register is used to enable the FIFOs, clear the FIFOs, set the receive FIFO trigger levels, and select the
DMA mode. The DMA, and FIFO modes are defined as follows:
FCR[0]: TX and RX FIFO Enable
Logic 0 = Disable the transmit and receive FIFO (default).
Logic 1 = Enable the transmit and receive FIFOs. This bit must be set to logic 1 when other FCR bits are
written or they will not be programmed.
FCR[1]: RX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No receive FIFO reset (default).
Logic 1 = Reset the receive FIFO pointers and FIFO level counter logic (the receive shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[2]: TX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No transmit FIFO reset (default).
Logic 1 = Reset the transmit FIFO pointers and FIFO level counter logic (the transmit shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[3]: DMA Mode Select
Controls the behavior of the TXRDY# and RXRDY# pins. See DMA operation section for details.
Logic 0 = Normal Operation (default).
Logic 1 = DMA Mode.
FCR[5:4]: Reserved (Default 0)
FCR[7:6]: Receive FIFO Trigger Select
(logic 0 = default, RX trigger level =1)
These 2 bits are used to set the trigger level for the receive FIFO. The UART will issue a receive interrupt when
the number of the characters in the FIFO crosses the trigger level. Table 10 shows the complete selections.
TABLE 10: RECEIVE FIFO TRIGGER LEVEL SELECTION
FCR BIT-7
FCR BIT-6
RECEIVE TRIGGER LEVEL
0
1
0
1
0
1
4
8
14
相關PDF資料 |
PDF描述 |
|---|---|
| ST1803DHI | High Voltage Fast-Switching NPN Power Transistor(高電壓快速開關NPN功率晶體管) |
| ST180S16P1PBF | 314 A, 1600 V, SCR, TO-209AB |
| ST1W008S4A | 8 CONTACT(S), MALE, PCMCIA CONNECTOR, SOLDER |
| ST203C12CCJ1P | 700 A, 1200 V, SCR, TO-200AB |
| ST203C12CCJ2LP | 700 A, 1200 V, SCR, TO-200AB |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C554DCJ-68 | 制造商:Exar Corporation 功能描述:IC,UART,LDCC,68PIN,PLASTIC |
| ST16C554DCJ68-F | 功能描述:UART 接口集成電路 2.97V-5.5V 16B FIFO temp -45 to 85C;UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C554DCJ68TR | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| ST16C554DCJ68TR-F | 功能描述:UART 接口集成電路 QUAD UART W/16 BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C554DCQ-0A-EB | 功能描述:界面開發工具 Supports C554D 64 ld TQFP, ISA Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
發布緊急采購，3分鐘左右您將得到回復。