參數資料
型號： ST16C552A
廠商： Exar Corporation
英文描述： Dual UART with 16-Byte FIFO and Parallel Printer Port(雙通用異步接收器/發送器（帶16字節的先進先出和并行打印機端口）)
中文描述： 雙UART），16字節FIFO和并行打印機端口（雙通用異步接收器/發送器（帶16字節的先進先出和并行打印機端口）
文件頁數： 25/40頁
文件大?。?/td> 463K
代理商： ST16C552A
25
ST16C552/552A
Rev. 3.30
source driver and internal pull-up so that it may be
wire-ord with other outputs. COM bit-1 is used to read
status while CON bit 1 is used to set an output state.
If it is to function as an input, CON bit-1 shall be set to
a logic 1 first.
Logic 0 = -STROBE pin is a logic 1. (normal default
condition)
Logic 1 = -STROBE pin is a logic 0.
COM BIT-1:
-AutoFDXT is a bi-directional signal with an open
source driver and internal pull-up so that it may be
wire-ord with other outputs. COM bit-1 is used to read
status while CON bit 1 is used to set an output state.
If it is to function as an input, CON bit-1 shall be set to
a logic 1 first.
Logic 0 = -AutoFDXT pin is a logic 1. (normal default
condition)
1= -AutoFDXT pin is a logic 0.
COM BIT-2:
INIT is a bi-directional signal with an open source
driver and internal pull-up so that it may be wire-ord
with other outputs. COM bit-2 is used to read status
while CON bit 2 is used to set an output state. If it is to
function as an input, CON bit-1 shall be set to a logic
1 first.
Logic 0 = INIT pin is a logic 0. (normal default
condition)
Logic 1 = INIT pin is a logic 1.
COM BIT-3:
-SLCTIN is a bi-directional signal with an open source
driver and internal pull-up so that it may be wire-ord
with other outputs. COM bit-1 is used to read status
while CON bit 1 is used to set an output state. If it is to
function as an input, CON bit-1 shall be set to a logic
1 first.
Logic 0 = -SLCTIN pin is a logic 1 (normal default
condition)
Logic 1 = -SLCTIN pin is a logic 0
COM BIT-4:
This bit allows the state of -INTP to be read back by the
external CPU.
Logic 0 = Interrupt (-INTP output) is disabled (normal
default condition)
Logic 1 = Interrupt (-INTP output) is enabled
COM BIT 5-7:
Not Used - initialized to a logic 1.
Control Register (CON)
This register provides control of the printer port output
logical states and controls the printer interrupts INIT
and -INTP. With the exception of PD 0-7 IN/OUT, the
status of this register may be read by reading the COM
register.
CON BIT-0:
The -STROBE output control bit is under software
control, i.e., the hardware will not generate a strobe. It
is up to software to return the state of -STROBE to the
inactive (logic 1) state. The hardware driver is open
drain so that -STROBE may be wire-ord. The state of
this bit can be read using COM bit-0.
Logic 0 = -STROBE output is set to a logic 1. (normal
default condition)
Logic 1 = -STROBE output is set to a logic 0.
CON BIT-1:
The -AutoFDXT output control bit is set by software
using CON bit-1. The hardware driver is open drain so
that -AutoFDXT may be wire-ord. The state of this bit
can be read using COM bit-1.
Logic 0 = -AutoFDXT output is set to a logic 1. (normal
default condition)
Logic 1 = -AutoFDXT output is set to a logic 0.
CON BIT-2:
The INIT output control bit is set by software using
CON bit-2. The hardware driver is open drain so that
INIT may be wire-ord. The state of this bit can be read
using COM bit-2.
Logic 0 = INIT output is set to a logic 0. (normal default
condition)
Logic 1 = INIT output is set to a logic 1.
CON BIT-3:
The -SLCTIN output control bit is set by software using
CON bit-3. The hardware driver is open drain so that
-AutoFDXT may be wire-ord. The state of this bit can
be read using COM bit-3.
相關PDF資料
PDF描述
ST16C554DCJ68 QUAD UART WITH 16-BYTE FIFOS
ST68C554 QUAD UART WITH 16-BYTE FIFOS
ST16C554DIJ68 Plug-In Relay; Contacts:DPDT; Contact Carry Current:15A; Coil Voltage AC Max:120V; Relay Mounting:Plug-In; Relay Terminals:Quick Connect; Coil Resistance:4430ohm RoHS Compliant: Yes
ST16C554DIQ64 QUAD UART WITH 16-BYTE FIFOS
ST16C554CQ64 Linear Voltage Regulator IC; Output Current Max:350mA; Supply Voltage Max:6V; Package/Case:8-TSSOP; Current Rating:350mA; Leaded Process Compatible:No; Output Voltage Max:2.8V; Peak Reflow Compatible (260 C):No
相關代理商/技術參數
參數描述
ST16C552ACJ68 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:
ST16C552ACJ68-F 功能描述:UART 接口集成電路 DUAL UART W/16BYTE FIFO&PARALELPRNTPORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
ST16C552ACJ68TR-F 功能描述:UART 接口集成電路 DUAL UART W/16BYTE FIFO&PARALELPRNTPORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
ST16C552AIJ68 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UART WITH 16-BYTE FIFO AND PARALLEL PRINTER PORT
ST16C552AIJ68-F 功能描述:UART 接口集成電路 DUAL UART W/16BYTE FIFO&PARALELPRNTPORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*