- 您現在的位置：買賣IC網 > PDF目錄383837 > ST16C550 (Exar Corporation) UART with 16-Byte FIFO(通用異步接收器/發送器（帶16字節的先進先出）) PDF資料下載
參數資料
| 型號： | ST16C550 |
| 廠商： | Exar Corporation |
| 英文描述： | UART with 16-Byte FIFO(通用異步接收器/發送器（帶16字節的先進先出）) |
| 中文描述： | 的UART具有16字節FIFO（通用異步接收器/發送器（帶16字節的先進先出）） |
| 文件頁數： | 19/36頁 |
| 文件大?。?/td> | 235K |
| 代理商： | ST16C550 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
ST16C550
19
Rev. 4.20
this bit causes the UART to issue an interrupt to CPU
when the THR interrupt enable is set. The THR bit is set
to a logic 1 when a character is transferred from the
transmit holding register into the transmitter shift regis-
ter. The bit is reset to logic 0 concurrently with the
loading of the transmitter holding register by the CPU.
In the FIFO mode this bit is set when the transmit FIFO
is empty; it is cleared when at least 1 byte is written to
the transmit FIFO.
LSR BIT-6:
This bit is the Transmit Empty indicator. This bit is set
to a logic 1 whenever the transmit holding register and
the transmit shift register are both empty. It is reset to
logic 0 whenever either the THR or TSR contains a
data character. In the FIFO mode this bit is set to one
whenever the transmit FIFO and transmit shift register
are both empty.
LSR BIT-7:
Logic 0 = No Error (normal default condition)
Logic 1 = At least one parity error, framing error or
break indication is in the current FIFO data. This bit is
cleared when there are no remaining LSR errors in the
RX FIFO.
Modem Status Register (MSR)
This register provides the current state of the control
interface signals from the modem, or other peripheral
device that the ST16C550 is connected to. Four bits
of this register are used to indicate the changed
information. These bits are set to a logic 1 whenever
a control input from the modem changes state. These
bits are set to a logic 0 whenever the CPU reads this
register.
MSR BIT-0:
Logic 0 = No -CTS Change (normal default condition)
Logic 1 = The -CTS input to the ST16C550 has
changed state since the last time it was read. A
modem Status Interrupt will be generated.
MSR BIT-1:
Logic 0 = No -DSR Change (normal default condition)
Logic 1 = The -DSR input to the ST16C550 has
changed state since the last time it was read. A
modem Status Interrupt will be generated.
MSR BIT-2:
Logic 0 = No -RI Change (normal default condition)
Logic 1 = The -RI input to the ST16C550 has changed
from a logic 0 to a logic 1. A modem Status Interrupt
will be generated.
MSR BIT-3:
Logic 0 = No -CD Change (normal default condition)
Logic 1 = Indicates that the -CD input to the has
changed state since the last time it was read. A
modem Status Interrupt will be generated.
MSR BIT-4:
CTS (active high, logical 1). Normally this bit is the
compliment of the -CTS input. In the loop-back mode,
this bit is equivalent to the RTS bit in the MCR register.
MSR BIT-5:
DSR (active high, logical 1). Normally this bit is the
compliment of the -DSR input. In the loop-back mode,
this bit is equivalent to the DTR bit in the MCR register.
MSR BIT-6:
RI (active high, logical 1). Normally this bit is the
compliment of the -RI input. In the loop-back mode
this bit is equivalent to the OP1 bit in the MCR register.
MSR BIT-7:
CD (active high, logical 1). Normally this bit is the
compliment of the -CD input. In the loop-back mode
this bit is equivalent to the OP2 bit in the MCR register.
Scratchpad Register (SPR)
The ST16C550 provides a temporary data register to
store 8 bits of user information.
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C552 | Dual UART with 16-Byte FIFO and Parallel Printer Port(雙通用異步接收器/發送器（帶16字節的先進先出和并行打印機端口）) |
| ST16C552A | Dual UART with 16-Byte FIFO and Parallel Printer Port(雙通用異步接收器/發送器（帶16字節的先進先出和并行打印機端口）) |
| ST16C554DCJ68 | QUAD UART WITH 16-BYTE FIFOS |
| ST68C554 | QUAD UART WITH 16-BYTE FIFOS |
| ST16C554DIJ68 | Plug-In Relay; Contacts:DPDT; Contact Carry Current:15A; Coil Voltage AC Max:120V; Relay Mounting:Plug-In; Relay Terminals:Quick Connect; Coil Resistance:4430ohm RoHS Compliant: Yes |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C550_05 | 制造商:EXAR 制造商全稱:EXAR 功能描述:UART WITH 16-BYTE FIFO’s |
| ST16C550CJ44 | 制造商:Exar 功能描述:Bulk |
| ST16C550CJ44-F | 功能描述:UART 接口集成電路 2.97V-5.5V 16B FIFO temp 0C to 70C; UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C550CJ44TR-F | 功能描述:UART 接口集成電路 SNGL UART W/16BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C550CP40 | 功能描述:UART 接口集成電路 SINGLE UART W/16 BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。