- 您現在的位置：買賣IC網 > PDF目錄3767 > ST16C450IQ48-F (Exar Corporation)IC UART SINGLE 48TQFP PDF資料下載
參數資料
| 型號： | ST16C450IQ48-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 8/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART SINGLE 48TQFP |
| 標準包裝： | 250 |
| 特點： | * |
| 通道數： | 1，UART |
| FIFO's： | 1 字節 |
| 電源電壓： | 2.97 V ~ 5.5 V |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-TQFP |
| 供應商設備封裝： | 48-TQFP（7x7） |
| 包裝： | 托盤 |
| 其它名稱： | 1016-1667 ST16C450IQ48-F-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
ST16C450
16
Rev. 4.20
LSR BIT-3:
Logic 0 = No framing error (normal default condition).
Logic 1 = Framing error. The receive character did not
have a valid stop bit(s).
LSR BIT-4:
Logic 0 = No break condition (normal default condi-
tion)
Logic 1 = The receiver received a break signal.
LSR BIT-5:
This bit indicates that the ST16C450 is ready to accept
new characters for transmission. This bit causes the
ST16C450 to issue an interrupt to the CPU when the
transmit holding register is empty and the interrupt
enable is set.
Logic 0 = Transmit holding register is not empty.
(normal default condition)
Logic 1 = Transmit holding register is empty. When
this bit is a logic 1, the CPU can load a new characters
into the Transmit Holding Register for transmission.
LSR BIT-6:
Logic 0 = Transmitter holding and shift registers are
full.
Logic 1 = Transmitter holding and shift registers are
empty.
LSR BIT-7: Not used and set to “0”.
Modem Status Register (MSR)
This register provides the current state of the control
interface signals from the modem, or other peripheral
device that the ST16C450 is connected to. Four bits
of this register are used to indicate the changed
information. These bits are set to a logic 1 whenever
a control input from the modem changes state. These
bits are set to a logic 0 whenever the CPU reads this
register.
MSR BIT-0:
Logic 0 = No -CTS Change (normal default condition)
Logic 1 = The -CTS input to the ST16C450 has
changed state since the last time it was read. A
modem Status Interrupt will be generated.
MSR BIT-1:
Logic 0 = No -DSR Change (normal default condition)
Logic 1 = The -DSR input to the ST16C450 has
changed state since the last time it was read. A
modem Status Interrupt will be generated.
MSR BIT-2:
Logic 0 = No -RI Change (normal default condition)
Logic 1 = The -RI input to the ST16C450 has changed
from a logic 0 to a logic 1. A modem Status Interrupt
will be generated.
MSR BIT-3:
Logic 0 = No -CD Change (normal default condition)
Logic 1 = Indicates that the -CD input to the has
changed state since the last time it was read. A
modem Status Interrupt will be generated.
MSR BIT-4:
CTS (active high, logical 1). Normally this bit is the
compliment of the -CTS input. In the loop-back mode,
this bit is equivalent to the RTS bit in the MCR register.
MSR BIT-5:
DSR (active high, logical 1). Normally this bit is the
compliment of the -DSR input. In the loop-back mode,
this bit is equivalent to the DTR bit in the MCR register.
MSR BIT-6:
RI (active high, logical 1). Normally this bit is the
compliment of the -RI input. In the loop-back mode this
bit is equivalent to the OP1 bit in the MCR register.
MSR BIT-7:
CD (active high, logical 1). Normally this bit is the
compliment of the -CD input. In the loop-back mode
this bit is equivalent to the OP2 bit in the MCR register.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX7324AEG+T | IC I/O EXPANDER I2C 8B 24QSOP |
| ATMEGA88-20MUR | MCU AVR 8K FLASH 20MHZ 32QFN |
| XR16M570IL24-F | IC UART FIFO 16B 24QFN |
| MAX7318AWG+ | IC PORT EXPANDER 16BIT 24SOIC |
| XR16M581IL24-F | IC UART FIFO 16B 24QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C450IQ48TR-F | 制造商:Exar Corporation 功能描述:UART 1-CH 1Byte FIFO 3.3V/5V 48-Pin TQFP T/R 制造商:Exar Corporation 功能描述:ST16C450 Series 1.5 Mbps 5.5 V Universal Asynchronous UART - TQFP-48 制造商:Exar Corporation 功能描述:ST16C450IQ48TR-F |
| ST16C452 | 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UART WITH PARALLEL PRINTER PORT |
| ST16C452CJ68 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:UART 2-CH 3.3V/5V 68-Pin PLCC |
| ST16C452CJ68-F | 功能描述:UART 接口集成電路 DUAL UART W/PARALEL PRINTER PORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C452CJ68PS | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。