- 您現在的位置：買賣IC網 > PDF目錄384931 > ST16C450IP40 (EXAR CORP) UNIVERSAL ASYNCHRONOUS RECEIVER/TRANSMITTER (UART) PDF資料下載
參數資料
| 型號： | ST16C450IP40 |
| 廠商： | EXAR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | UNIVERSAL ASYNCHRONOUS RECEIVER/TRANSMITTER (UART) |
| 中文描述： | 1 CHANNEL(S), 1.5M bps, SERIAL COMM CONTROLLER, PDIP40 |
| 封裝： | DIP-40 |
| 文件頁數： | 6/28頁 |
| 文件大?。?/td> | 182K |
| 代理商： | ST16C450IP40 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
ST16C450
6
Rev. 4.20
-OP2
31
35
31
O
Output-2 (User Defined). This pin provides the user a general
purpose output. See bit-3 modem control register (MCR bit-
3).
VCC
40
44
42
Pwr
Power Supply Input.
XTAL1
16
18
14
I
Crystal or External Clock Input - Functions as a crystal input
or as an external clock input. A crystal can be connected
between this pin and XTAL2 to form an internal oscillator
circuit. An external 1 MW resistor is required between the
XTAL1 and XTAL2 pins (see figure 3). Alternatively, an
external clock can be connected to this pin to provide
custom data rates (Programming Baud Rate Generator
section).
XTAL2
17
19
15
O
Output of the Crystal Oscillator or Buffered Clock - (See also
XTAL1). Crystal oscillator output or buffered clock output.
-CD
38
42
40
I
Carrier Detect (active low) - A logic 0 on this pin indicates
that a carrier has been detected by the modem.
-CTS
36
40
38
I
Clear to Send (active low) - A logic 0 on the -CTS pin
indicates the modem or data set is ready to accept transmit
data from the ST16C450. Status can be tested by reading
MSR bit-4. This pin has no effect on the UART’s transmit or
receive operation.
-DSR
37
41
39
I
Data Set Ready (active low) - A logic 0 on this pin indicates
the modem or data set is powered-on and is ready for data
exchange with the UART. This pin has no effect on the
UART’s transmit or receive operation.
-DTR
33
37
33
O
Data Terminal Ready (active low) - A logic 0 on this pin
indicates that the ST16C450 is powered-on and ready. This
pin can be controlled via the modem control register.
Writing a logic 1 to MCR bit-0 will set the -DTR output to
logic 0, enabling the modem. This pin will be a logic 1 after
writing a logic 0 to MCR bit-0, or after a reset. This pin has
no effect on the UART’s transmit or receive operation.
SYMBOL DESCRIPTION
Symbol
Pin
44
Signal
type
Pin Description
40
48
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C450IQ48 | UNIVERSAL ASYNCHRONOUS RECEIVER/TRANSMITTER (UART) |
| ST16C454 | QUAD UNIVERSAL ASYNCHRONOUS RECEIVER/TRANSMITTER (UART) |
| ST16C454CJ68 | QUAD UNIVERSAL ASYNCHRONOUS RECEIVER/TRANSMITTER (UART) |
| ST16C454IJ68 | QUAD UNIVERSAL ASYNCHRONOUS RECEIVER/TRANSMITTER (UART) |
| ST68C454 | QUAD UNIVERSAL ASYNCHRONOUS RECEIVER/TRANSMITTER (UART) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C450IP40-F | 功能描述:UART 接口集成電路 SINGLE UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C450IQ48 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| ST16C450IQ48-F | 功能描述:UART 接口集成電路 SINGLE UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C450IQ48TR-F | 制造商:Exar Corporation 功能描述:UART 1-CH 1Byte FIFO 3.3V/5V 48-Pin TQFP T/R 制造商:Exar Corporation 功能描述:ST16C450 Series 1.5 Mbps 5.5 V Universal Asynchronous UART - TQFP-48 制造商:Exar Corporation 功能描述:ST16C450IQ48TR-F |
| ST16C452 | 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UART WITH PARALLEL PRINTER PORT |
發布緊急采購，3分鐘左右您將得到回復。