參數資料
型號: ST16C2552IJ
廠商: EXAR CORP
元件分類: 微控制器/微處理器
英文描述: 2.97V TO 5.5V DUAL UART WITH 16-BYTE FIFO
中文描述: 2 CHANNEL(S), 4M bps, SERIAL COMM CONTROLLER, PQCC44
封裝: PLASTIC, LCC-44
文件頁數: 10/28頁
文件大?。?/td> 121K
代理商: ST16C2552IJ
3-144
ST16C2552
S
BIT-2
BIT-1
MF* Function
0
0
1
1
0
1
0
1
OP2*
BAUDOUT*
RXRDY*
Reserved
AFR BIT 3-7:
Not used. All these bits are set to logic zero.
LINE CONTROL REGISTER (LCR)
The Line Control Register is used to specify the
asynchronous data communication format. The num-
ber of the word length, stop bits, and parity can be
selected by writing appropriate bits in this register.
LCR BIT1-0:
These two bits specify the word length to be transmit-
ted or received.
BIT-1
BIT-0
Word length
0
0
1
1
0
1
0
1
5
6
7
8
LCR BIT-2:
The number of stop bits can be specified by this bit.
BIT-2
Word length
Stop bit(s)
0
1
1
5,6,7,8
5
6,7,8
1
1-1/2
2
LCR BIT-3:
Parity or no parity can be selected via this bit.
0=no parity
1=a parity bit is generated during the transmission,
receiver also checks for received parity.
LCR BIT-4:
If the parity bit is enabled, LCR BIT-4 selects the even
or odd parity format.
0=ODD parity is generated by forcing an odd number
of 1’s in the transmitted data, receiver also checks for
same format.
1= EVEN parity
bit is generated by forcing an even
number of 1’s in the transmitted data, receiver also
checks for same format.
LCR BIT-5:
If the parity bit is enabled, LCR BIT-5 selects the
forced parity format.
LCR BIT-5=1 and LCR BIT-4=0, parity bit is forced to
“1” in the transmitted and received data.
LCR BIT-5=1 and LCR BIT-4=1, parity bit is forced to
“0” in the transmitted and received data.
LCR BIT-6:
Break control bit. It causes a break condition to be
transmitted (the TX is forced to low state).
0=normal operating condition.
1=forces the transmitter output (TX) to go low to alert
the communication terminal.
LCR BIT-7:
The internal baud rate counter latch enable (DLAB).
0=normal operation.
1=select Divisor Latch Register and Alternate Func-
tion Register.
MODEM CONTROL REGISTER (MCR)
This register controls the interface with the MODEM
or a peripheral device (RS232).
MCR BIT-0:
0=force DTR* output to high.
1=force DTR* output to low.
MCR BIT-1:
0=force RTS* output to high.
1=force RTS* output to low.
相關PDF資料
PDF描述
ST16C452IJ68 DUAL UART WITH PARALLEL PRINTER PORT
ST16C452IJ68PS DUAL UART WITH PARALLEL PRINTER PORT
ST16C452CJ68 Power Supply IC; Number of Outputs:1; Supply Voltage Max:5.5V; Package/Case:10-MSOP; Leaded Process Compatible:No; Output Current:150mA; Output Voltage Max:1.3V; Peak Reflow Compatible (260 C):No; Power Dissipation:481mW
ST16C452CJ68PS Power Supply IC; Number of Outputs:1; Supply Voltage Max:5.5V; Package/Case:10-MSOP; Leaded Process Compatible:No; Output Current:150mA; Output Voltage Max:1.3V; Peak Reflow Compatible (260 C):No; Power Dissipation:481mW
ST16C452PS Dual UART with Parallel Printer Port(雙通用異步接收器/發送器(帶并行打印機端口))
相關代理商/技術參數
參數描述
ST16C2552IJ44 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: 制造商:Exar Corporation 功能描述:UART, 44 Pin, Plastic, PLCC
ST16C2552IJ44-F 功能描述:UART 接口集成電路 2.97V-5.5V 16B FIFO temp -45 to 85C;UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
ST16C2552IJ44TR-F 功能描述:UART 接口集成電路 DUAL UART W/16BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
ST16C2552IQ48 制造商:未知廠家 制造商全稱:未知廠家 功能描述:UART
ST16C32245 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:14 BIT DUAL SUPPLY BUS TRANSCEIVER LEVEL TRANSLATOR, A SIDE SERIES RESISTOR, 2 BIT I2C LINES