- 您現在的位置：買賣IC網 > PDF目錄384930 > ST16C2550IJ44 (EXAR CORP) DUAL UART WITH 16-BYTE TRANSMIT AND RECEIVE FIFO’S PDF資料下載
參數資料
| 型號： | ST16C2550IJ44 |
| 廠商： | EXAR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | DUAL UART WITH 16-BYTE TRANSMIT AND RECEIVE FIFO’S |
| 中文描述： | 2 CHANNEL(S), 4M bps, SERIAL COMM CONTROLLER, PQCC44 |
| 封裝： | PLASTIC, LCC-44 |
| 文件頁數： | 17/34頁 |
| 文件大?。?/td> | 443K |
| 代理商： | ST16C2550IJ44 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
ST16C2550
17
Rev. 3.20
FCR BIT-3:
Logic 0 = Set DMA mode 0. (normal default condi-
tion)
Logic 1 = Set DMA mode 1.
Transmit operation in mode 0:
When the 2550 is in the ST16C450 mode (FIFOs
disabled, FCR bit-0 = logic 0) or in the FIFO mode
(FIFOs enabled, FCR bit-0 = logic 1, FCR bit-3 = logic
0) and when there are no characters in the transmit
FIFO or transmit holding register, the -TXRDY pin in
44/48 pin packages will be a logic 0. Once active the
-TXRDY pin will go to a logic 1 after the first character
is loaded into the transmit holding register.
Receive operation in mode 0:
When the 2550 is in mode 0 (FCR bit-0 = logic 0) or
in the FIFO mode (FCR bit-0 = logic 1, FCR bit-3 =
logic 0) and there is at least one character in the
receive FIFO, the -RXRDY pin will be a logic 0. Once
active the -RXRDY pin on 44/48 pin packages will go
to a logic 1 when there are no more characters in the
receiver.
Transmit operation in mode 1:
When the 2550 is in FIFO mode ( FCR bit-0 = logic 1,
FCR bit-3 = logic 1 ), the -TXRDY pin on 44/48 pin
packages will be a logic 1 when the transmit FIFO is
completely full. It will be a logic 0 if one or more FIFO
locations are empty.
Receive operation in mode 1:
When the 2550 is in FIFO mode (FCR bit-0 = logic 1,
FCR bit-3 = logic 1) and the trigger level has been
reached, or a Receive Time Out has occurred, the -
RXRDY pin on 44/48 pin packages will go to a logic 0.
Once activated, it will go to a logic 1 after there are no
more characters in the FIFO.
FCR BIT 4-5:
Not Used - initialized to a logic 0.
FCR BIT 6-7: (logic 0 or cleared is the default condi-
tion, RX trigger level = 1)
These bits are used to set the trigger level for the
receive FIFO interrupt.
An interrupt is generated when the number of charac-
ters in the FIFO equals the programmed trigger level.
However the FIFO will continue to be loaded until it is
full.
BIT-7
BIT-6
RX FIFO trigger level
0
0
1
1
0
1
0
1
01
04
08
14
Interrupt Status Register (ISR)
The 2550 provides four levels of prioritized interrupts
to minimize external software interaction. The Inter-
rupt Status Register (ISR) provides the user with four
interrupt status bits. Performing a read cycle on the
ISR will provide the user with the highest pending
interrupt level to be serviced. No other interrupts are
acknowledged until the pending interrupt is serviced.
Whenever the interrupt status register is read, the
interrupt status is cleared. However it should be noted
that only the current pending interrupt is cleared by the
read. A lower level interrupt may be seen after reread-
ing the interrupt status bits. The Interrupt Source
Table 6 (below) shows the data values (bits 0-3) for the
four prioritized interrupt levels and the interrupt
sources associated with each of these interrupt levels:
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C2550IP40 | DUAL UART WITH 16-BYTE TRANSMIT AND RECEIVE FIFO’S |
| ST16C2550CJ44 | DUAL UART WITH 16-BYTE TRANSMIT AND RECEIVE FIFO’S |
| ST16C2550CP40 | Power Supply IC; Supply Voltage Max:6V; Output Voltage:1.3V; Package/Case:20-TSSOP; Leaded Process Compatible:No; Output Voltage Max:1.3V; Peak Reflow Compatible (260 C):No; Supply Voltage Min:2.7V; Mounting Type:Surface Mount |
| ST16C2550IQ48 | DUAL UART WITH 16-BYTE TRANSMIT AND RECEIVE FIFO’S |
| ST16C2550 | Dual UART with 16-Byte of Transmit and Receive FIFO(雙通用異步接收器/發送器（帶16字節接收和發送先進先出）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C2550IJ44-F | 功能描述:UART 接口集成電路 DUAL UART W/16BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C2550IJ44TR-F | 制造商:Exar Corporation 功能描述:UART 2-CH 16Byte FIFO 3.3V/5V 44-Pin PLCC T/R 制造商:Exar Corporation 功能描述:ST16C2550IJ44TR-F |
| ST16C2550IP40 | 功能描述:UART 接口集成電路 DUAL UART W/16 BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C2550IQ48 | 制造商:Rochester Electronics LLC 功能描述: |
| ST16C2550IQ48-F | 功能描述:UART 接口集成電路 2.97V-5.5V 16B FIFO temp -45 to 85C;UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。