REV. 4.4.1 2.7 Crystal Oscillator or External Clock Input The C2550 includes an on-chip osci" />
參數資料
型號： ST16C2550CJ-0A-EB
廠商： Exar Corporation
文件頁數： 2/37頁
文件大?。?/td> 0K
描述： EVAL BOARD FOR ST16C2550 44PLCC
標準包裝： 1
系列： *
ST16C2550
10
2.97V TO 5.5V DUART WITH 16-BYTE FIFO
REV. 4.4.1
2.7
Crystal Oscillator or External Clock Input
The C2550 includes an on-chip oscillator (XTAL1 and XTAL2) to produce a clock for both UART sections in the
device. The CPU data bus does not require this clock for bus operation. The crystal oscillator provides a
system clock to the Baud Rate Generators (BRG) section found in each of the UART. XTAL1 is the input to the
oscillator or external clock buffer input with XTAL2 pin being the output. See “Programmable Baud Rate
FIGURE 4. TYPICAL OSCILLATOR CONNECTIONS
C1
22-47 pF
C2
22-47 pF
Y1
1.8432 MHz
to
24 MHz
R1
0-120
(Optional)
R2
500 Κ 1 Μ
XTAL1
XTAL2
The on-chip oscillator is designed to use an industry standard microprocessor crystal (parallel resonant,
fundamental frequency with 10-22 pF capacitance load, ESR of 20-120 ohms and 100ppm frequency
tolerance) connected externally between the XTAL1 and XTAL2 pins (see Figure 4), with an external 500k
to
1 M
resistor across it. Alternatively, an external clock can be connected to the XTAL1 pin to clock the internal
baud rate generator for standard or custom rates. Typical oscillator connections are shown in Figure 4. For
further reading on oscillator circuit please see application note DAN108 on EXAR’s web site.
2.8
Programmable Baud Rate Generator
A single baud rate generator is provided for the transmitter and receiver, allowing independent TX/RX channel
control. The programmable Baud Rate Generator is capable of operating with a crystal frequency of up to 24
MHz. However, with an external clock input on XTAL1 pin and a 2K ohms pull-up resistor on XTAL2 pin (as
shown in Figure 5) it can extend its operation up to 64 MHz (4Mbps serial data rate) at room temperature and
5.0V.
相關PDF資料
PDF描述
MFP 1/8"CR48"BX HTSHRNK MFP 1/8"X4'(8')CLR
UPA1E122MHD1TO CAP ALUM 1200UF 25V 20% RADIAL
VE-20T-EX CONVERTER MOD DC/DC 6.5V 75W
RP60-4812SG-HC CONV DC/DC 60W 36-75VIN 12VOUT
ESM10DRTH-S13 CONN EDGECARD 20POS .156 EXTEND
相關代理商/技術參數
參數描述
ST16C2550CJ44 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V DUART WITH 16-BYTE FIFO
ST16C2550CJ44-F 功能描述:UART 接口集成電路 2.97V-5.5V 16B FIFO temp 0C to 70C; UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
ST16C2550CJ44TR-F 功能描述:UART 接口集成電路 DUAL UART W/16BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
ST16C2550CP40 功能描述:UART 接口集成電路 DUAL UART W/16 BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
ST16C2550CP40-F 功能描述:UART 接口集成電路 DUAL UART W/16 BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*