- 您現在的位置：買賣IC網 > PDF目錄383836 > ST16C2450 (Exar Corporation) 2.97V TO 5.5V DUART PDF資料下載
參數資料
| 型號： | ST16C2450 |
| 廠商： | Exar Corporation |
| 英文描述： | 2.97V TO 5.5V DUART |
| 中文描述： | 2.97V至5.5V杜阿爾特 |
| 文件頁數： | 17/29頁 |
| 文件大?。?/td> | 315K |
| 代理商： | ST16C2450 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
á
REV. 4.0.0
ST16C2450
2.97V TO 5.5V DUART
17
LCR[7]: Baud Rate Divisors (DLL/DLM) Enable
Logic 0 = Data registers are selected (default).
Logic 1 = Divisor latch registers are selected.
4.6
Modem Control Register (MCR) or General Purpose Outputs Control - Read/Write
The MCR register is used for controlling the serial/modem interface signals or general purpose inputs/outputs.
MCR[0]: DTR# Output
The DTR# pin is a modem control output. If the modem interface is not used, this output may be used as a
general purpose output.
Logic 0 = Force DTR# output to a logic 1 (default).
Logic 1 = Force DTR# output to a logic 0.
MCR[1]: RTS# Output
The RTS# pin is a modem control output. If the modem interface is not used, this output may be used as a
general purpose output.
Logic 0 = Force RTS# output to a logic 1 (default).
Logic 1 = Force RTS# output to a logic 0.
MCR[2]: Reserved
OP1# is not available as an output pin on the 2450. But it is available for use during Internal Loopback Mode. In
the Loopback Mode, this bit is used to write the state of the modem RI# interface signal.
MCR[3]: OP2# Output / INT Output Enable
This bit enables and disables the operation of INT, interrupt output. If INT output is not used, OP2# can be used
as a general purpose output.
Logic 0 = INT (A-B) outputs disabled (three state mode) and OP2# output set to a logic 1 (default).
Logic 1 = INT (A-B) outputs enabled (active mode) and OP2# output set to a logic 0.
MCR[4]: Internal Loopback Enable
Logic 0 = Disable loopback mode (default).
Logic 1 = Enable local loopback mode, see loopback section and
Figure 7
.
MCR[7:5]: Reserved
4.7
Line Status Register (LSR) - Read Only
This register provides the status of data transfers between the UART and the host.
LSR[0]: Receive Data Ready Indicator
Logic 0 = No data in receive holding register or FIFO (default).
Logic 1 = Data has been received and is saved in the receive holding register .
LSR[1]: Receiver Overrun Flag
Logic 0 = No overrun error (default).
Logic 1 = Overrun error. A data overrun error condition occurred in the receive shift register. This happens
when additional data arrives while there is data in the RHR. In this case the previous data in the receive shift
register is overwritten. Note that under this condition the data byte in the receive shift register is not
transferred into the RHR, therefore the data in the RHR is not corrupted by the error. An interrupt will be
generated immediately if LSR interrupt is enabled (IER bit-2).
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C2450CJ44 | 2.97V TO 5.5V DUART |
| ST16C2450CP40 | 2.97V TO 5.5V DUART |
| ST16C2450CQ48 | 2.97V TO 5.5V DUART |
| ST16C2450IJ44 | 2.97V TO 5.5V DUART |
| ST16C2450IP40 | 2.97V TO 5.5V DUART |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C2450_05 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V DUART |
| ST16C2450CJ-0A-EB | 功能描述:界面開發工具 Supports C2450 44 ld PLCC, ISA Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| ST16C2450CJ44 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| ST16C2450CJ44-F | 功能描述:UART 接口集成電路 DUAL UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C2450CJ44TR | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。