- 您現在的位置：買賣IC網 > PDF目錄383836 > ST16C1450CQ48 (STARTECH SEMICONDUCTOR INC) 2.97V TO 5.5V UART PDF資料下載
參數資料
| 型號： | ST16C1450CQ48 |
| 廠商： | STARTECH SEMICONDUCTOR INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 2.97V TO 5.5V UART |
| 中文描述： | 1 CHANNEL(S), 448K bps, SERIAL COMM CONTROLLER, PQFP48 |
| 文件頁數： | 18/32頁 |
| 文件大?。?/td> | 355K |
| 代理商： | ST16C1450CQ48 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
ST16C1450/51
2.97V TO 5.5V UART
á
REV. 4.2.0
18
LCR[5]: TX and RX Parity Select
If the parity bit is enabled, LCR BIT-5 selects the forced parity format.
LCR[5] = logic 0, parity is not forced (default).
LCR[5] = logic 1 and LCR[4] = logic 0, parity bit is forced to a logical 1 for the transmit and receive data.
LCR[5] = logic 1 and LCR[4] = logic 1, parity bit is forced to a logical 0 for the transmit and receive data.
LCR[6]: Transmit Break Enable
When enabled, the Break control bit causes a break condition to be transmitted (the TX output is forced to a
“space’, logic 0, state). This condition remains, until disabled by setting LCR bit-6 to a logic 0.
Logic 0 = No TX break condition (default).
Logic 1 = Forces the transmitter output (TX) to a “space”, logic 0, for alerting the remote receiver of a line
break condition.
LCR[7]: Baud Rate Divisors Enable
Baud rate generator divisor (DLL/DLM) enable.
Logic 0 = Data registers are selected (default).
Logic 1 = Divisor latch registers are selected.
4.6
Modem Control Register (MCR) or General Purpose Outputs Control - Read/Write
The MCR register is used for controlling the serial/modem interface signals or general purpose inputs/outputs.
MCR[0]: DTR# Output
The DTR# pin is a modem control output. If the modem interface is not used, this output may be used as a
general purpose output.
Logic 0 = Force DTR# output to a logic 1 (default).
Logic 1 = Force DTR# output to a logic 0.
MCR[1]: RTS# Output
The RTS# pin is a modem control output. If the modem interface is not used, this output may be used as a
general purpose output.
Logic 0 = Force RTS# output to a logic 1 (default).
Logic 1 = Force RTS# output to a logic 0.
T
ABLE
5: P
ARITY
SELECTION
LCR B
IT
-5 LCR B
IT
-4 LCR B
IT
-3
P
ARITY
SELECTION
X
X
0
No parity
0
0
1
Odd parity
0
1
1
Even parity
1
0
1
Force parity to mark,
“1”
1
1
1
Forced parity to
space, “0”
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C1450IJ28 | 2.97V TO 5.5V UART |
| ST16C1450IP28 | 2.97V TO 5.5V UART |
| ST16C1450IQ48 | 2.97V TO 5.5V UART |
| ST16C1451CJ28 | 2.97V TO 5.5V UART |
| ST16C1451CP28 | 2.97V TO 5.5V UART |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C1450CQ48-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C1450CQ48TR-F | 制造商:Exar Corporation 功能描述:UART 1-CH 1Byte FIFO 3.3V/5V 48-Pin TQFP T/R 制造商:Exar Corporation 功能描述:ST16C1450CQ48TR-F |
| ST16C1450IJ28 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V UART |
| ST16C1450IJ28-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C1450IP28 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.97V TO 5.5V UART |
發布緊急采購，3分鐘左右您將得到回復。