- 您現在的位置：買賣IC網 > PDF目錄2110 > SSM2380CBZ-REEL7 (Analog Devices Inc)IC AMP AUD 2X2W STER D 16WLCSP PDF資料下載
參數資料
| 型號： | SSM2380CBZ-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 6/32頁 |
| 文件大小： | 0K |
| 描述： | IC AMP AUD 2X2W STER D 16WLCSP |
| 產品變化通告： | 8mm Carrier Tape Changes 28/Feb/2012 |
| 標準包裝： | 1 |
| 類型： | D 類 |
| 輸出類型： | 2 通道（立體聲） |
| 在某負載時最大輸出功率 x 通道數量： | 3.2W x 2 @ 4 歐姆 |
| 電源電壓： | 2.5 V ~ 5.5 V |
| 特點： | 消除爆音，差分輸入，I²C，靜音，短路和熱保護 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 16-WLCSP |
| 封裝/外殼： | 16-UFBGA，WLCSP |
| 包裝： | 標準包裝 |
| 其它名稱： | SSM2380CBZ-REEL7DKR |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
SSM2380
Rev. A | Page 14 of 32
THEORY OF OPERATION
OVERVIEW
The SSM2380 stereo, Class-D audio amplifier features a filterless
modulation scheme that greatly reduces the external component
count, conserving board space and, thus, reducing system cost.
The SSM2380 does not require an output filter but, instead, relies
on the inherent inductance of the speaker coil and the natural
filtering of the speaker and human ear to fully recover the audio
component of the square wave output.
Most Class-D amplifiers use some variation of pulse-width
modulation (PWM), but the SSM2380 uses Σ-Δ modulation to
determine the switching pattern of the output devices, resulting
in a number of important benefits.
Σ-Δ modulators do not produce a sharp peak with many
harmonics in the AM frequency band, as pulse-width
modulators often do.
Σ-Δ modulation provides the benefits of reducing the
amplitude of spectral components at high frequencies,
that is, reducing EMI emissions that might otherwise
be radiated by speakers and long cable traces.
The SSM2380 does not require external EMI filtering for
twisted speaker cable lengths shorter than 10 cm. If longer
speaker cables are used, the SSM2380 has an emission sup-
pression mode that allows significantly longer speaker cable.
Due to the inherent spread-spectrum nature of Σ-Δ modu-
lation, the need for modulator synchronization is eliminated
for designs that incorporate multiple SSM2380 amplifiers.
Using the I2C control interface, the gain of the SSM2380 can
be selected from 1 dB to 24 dB (plus mute) in 47 steps with no
external components and fixed input impedance. Other features
accessed from the I2C interface include the following:
Independent left/right channel shutdown
Variable ultralow EMI emission control mode
Automatic level control (ALC) for high quality speaker
protection
Stereo-to-mono mixing operation
The SSM2380 also offers protection circuits for overcurrent and
overtemperature protection.
POP-AND-CLICK SUPPRESSION
Voltage transients at the output of audio amplifiers can occur
when shutdown is activated or deactivated. Voltage transients
as low as 10 mV can be heard as an audio pop in the speaker.
Clicks and pops can also be classified as undesirable audible
transients generated by the amplifier system and, therefore, as
not coming from the system input signal. Such transients may
be generated when the amplifier system changes its operating
mode. For example, the following may be sources of audible
transients: system power-up and power-down, mute and
unmute, input source change, and sample rate change.
The SSM2380 has a pop-and-click suppression architecture that
reduces these output transients, resulting in noiseless activation
and deactivation.
OUTPUT MODULATION DESCRIPTION
The SSM2380 uses three-level, Σ-Δ output modulation. Each
output can swing from GND to VDD and vice versa. Ideally, when
no input signal is present, the output differential voltage is 0 V
because there is no need to generate a pulse. In a real-world
situation, noise sources are always present.
Due to the constant presence of noise, a differential pulse is
generated, when required, in response to this stimulus. A small
amount of current flows into the inductive load when the differ-
ential pulse is generated.
Most of the time, however, the output differential voltage is 0 V,
due to the Analog Devices, Inc., three-level, Σ-Δ output modu-
lation. This feature ensures that the current flowing through the
inductive load is small.
When the user wants to send an input signal, an output pulse
(OUTx+ and OUTx) is generated to follow the input voltage.
The differential pulse density (VOUT) is increased by raising the
input signal level. Figure 35 depicts three-level, Σ-Δ output
modulation with and without input stimulus.
OUTPUT > 0V
+5V
0V
OUT+
+5V
0V
OUT–
+5V
0V
VOUT
OUTPUT < 0V
+5V
0V
OUT+
+5V
0V
OUT–
0V
–5V
VOUT
OUTPUT = 0V
OUT+
+5V
0V
+5V
0V
OUT–
+5V
–5V
0V
VOUT
08
75
2-
0
04
Figure 35. Three-Level, Σ-Δ Output Modulation
With and Without Input Stimulus
相關PDF資料 |
PDF描述 |
|---|---|
| SSM2517CBZ-RL | IC AMP AUDIO 2.4W MONO D 9WLCSP |
| SSM2518CPZ | IC AMP AUD PWR 2C STER D 20LFCSP |
| SSM2804CBZ-R7 | IC AMP AUDIO 1.4W SPKR 30WLSCP |
| SSM2932ACBZ-RL | IC HEADPHONE AMP STEREO 16WLCSP |
| SSM3302ACPZ-RL | IC AMP AUDIO 20W STER D 40LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SSM23LPT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SURFACE MOUNT SCHOTTKY BARRIER RECTIFIER VOLTAGE RANGE 20 - 40 Volts CURRENT 2.0 Amperes |
| SSM23PT | 制造商:CHENMKO 制造商全稱:Chenmko Enterprise Co. Ltd. 功能描述:SCHOTTKY BARRIER RECTIFIER |
| SSM2402 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual Audio Analog Switches |
| SSM-2402 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual Audio Analog Switches |
| SSM2402P | 制造商:Analog Devices 功能描述:Analog Switch Dual SPST 14-Pin PDIP N 制造商:Rochester Electronics LLC 功能描述:DUAL AUDIO SWITCH IC - Bulk 制造商:Analog Devices 功能描述:SWITCH DUAL SPST AUDIO 2402 DIP14 |
發布緊急采購，3分鐘左右您將得到回復。