- 您現在的位置：買賣IC網 > PDF目錄382545 > SPT7863 (Fairchild Semiconductor Corporation) 10-BIT, 40 MSPS, 160 mW A/D CONVERTER PDF資料下載
參數資料
| 型號： | SPT7863 |
| 廠商： | Fairchild Semiconductor Corporation |
| 英文描述： | 10-BIT, 40 MSPS, 160 mW A/D CONVERTER |
| 中文描述： | 10位，40 MSPS的，160毫瓦的A / D轉換器 |
| 文件頁數： | 8/11頁 |
| 文件大小： | 91K |
| 代理商： | SPT7863 |
8
8/21/01
SPT7863
Typically, the top side voltage drop for V
RHF
to V
RHS
will
equal:
V
RHF
–
V
RHS
= 2.25 % of (V
RHF
–
V
RLF
) (typical),
and the bottom side voltage drop for V
RLS
to V
RLF
will
equal:
V
RLS
–
V
RLF
= 1.9 % of (V
RHF
–
V
RLF
) (typical).
Figure 4 shows an example of expected voltage drops for
a specific case. V
REF
of 4.0 V is applied to V
RHF
, and V
RLF
is tied to AGND. A 90 mV drop is seen at V
RHS
(= 3.91 V),
and a 75 mV increase is seen at V
RLS
(= 0.075 V).
ANALOG INPUT
V
IN
is the analog input. The input voltage range is from
V
RLS
to V
RHS
(typically 4.0 V) and will scale proportionally
with respect to the voltage reference. (See voltage refer-
ence section.)
The drive requirements for the analog inputs are very
minimal when compared to most other converters due to
the SPT7863
’
s extremely low input capacitance of only
5 pF and very high input resistance in excess of 50 k
.
The analog input should be protected through a series
resistor and diode clamping circuit as shown in figure 5.
Upon powerup, the SPT7863 begins its calibration algo-
rithm. In order to achieve the calibration accuracy re-
quired, the offset and gain adjustment step size is a frac-
tion of a 10-bit LSB. Since the calibration algorithm is an
oversampling process, a minimum of 10,000 clock cycles
are required. This results in a minimum calibration time
upon powerup of 250 μsec (for a 40 MHz clock). Once
calibrated, the SPT7863 remains calibrated over time and
temperature.
Since the calibration cycles are initiated on the rising edge
of the clock, the clock must be continuously applied for the
SPT7863 to remain in calibration.
INPUT PROTECTION
All I/O pads are protected with an on-chip protection
circuit shown in figure 6. This circuit provides ESD robust-
ness to 3.5 kV and prevents latch-up under severe dis-
charge conditions without degrading analog transition
times.
Figure 5
–
Recommended Input Protection Circuit
8
32
#
%%
B
9#9:" C !$2#D- "
Figure 6
–
On-Chip Protection Circuit
"
!
#+
#+
CALIBRATION
The SPT7863 uses an auto-calibration scheme to ensure
10-bit accuracy over time and temperature. Gain and off-
set errors are continually adjusted to 10-bit accuracy
during device operation. This process is completely trans-
parent to the user.
POWER SUPPLY SEQUENCING CONSIDERATIONS
All logic inputs should be held low until power to the device
has settled to the specific tolerances. Avoid power decou-
pling networks with large time constants that could delay
V
DD
power to the device.
相關PDF資料 |
PDF描述 |
|---|---|
| SPT7871 | 10-BIT, 100 MSPS TTL A/D CONVERTER |
| SPT7871SCU | 10-BIT, 100 MSPS TTL A/D CONVERTER |
| SPT7871SIQ | 10-BIT, 100 MSPS TTL A/D CONVERTER |
| SPT7935 | 12-BIT, 20 MSPS, 79 mW A/D CONVERTER |
| SPT7935SIT | 12-BIT, 20 MSPS, 79 mW A/D CONVERTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SPT7863SCS | 功能描述:直流/直流開關轉換器 10BIT 40MSPS SaR aDC RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| SPT7863SCSX | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| SPT7863SCT | 功能描述:視頻模擬/數字化轉換器集成電路 10BIT 40MSPS SaR aDC RoHS:否 制造商:Texas Instruments 輸入信號類型:Differential 轉換器數量:1 ADC 輸入端數量:4 轉換速率:3 Gbps 分辨率:8 bit 結構: 輸入電壓:3.3 V 接口類型:SPI 信噪比: 電壓參考: 電源電壓-最大:3.45 V 電源電壓-最小:3.15 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:TCSP-48 封裝:Reel |
| SPT7863SCT_Q | 功能描述:模數轉換器 - ADC 10BIT 40MSPS SaR aDC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| SPT7863SCTX | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。