- 您現在的位置：買賣IC網 > PDF目錄10562 > SP505ACM-L (Exar Corporation)IC TXRX WAN MULTI-MODE 80LQFP PDF資料下載
參數資料
| 型號： | SP505ACM-L |
| 廠商： | Exar Corporation |
| 文件頁數： | 13/35頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX WAN MULTI-MODE 80LQFP |
| 標準包裝： | 84 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 7/7 |
| 規程： | 多協議 |
| 電源電壓： | 5V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 80-LQFP |
| 供應商設備封裝： | 80-LQFP（14x14） |
| 包裝： | 托盤 |
| 其它名稱： | 1016-1191 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
20
Exar Coporation 48720 Kato Road, Fremont CA, 94538 (50) 668-7000 Fax (50) 668-707 www.exar.com
SP505_00_08308
a load of 00. The signal levels and drive
capability of these drivers allow the drivers to
also support RS-485 requirements of ±.5V
minimumdifferentialoutputlevelswitha54
load. The driver is designed to operate over
a common mode range of +2V to -7V, which
follows the RS-485 specification. This also
covers the +7V to -7V common mode range
for V. (RS-422) requirements. The V.
drivers are used in RS-449, EIA-530, EIA-
530A and V.36 modes as Category I signals
which are used for clock and data signals.
V.35 Drivers
The fourth type of driver is the V.35 driver.
These drivers were specifically designed
to comply with the requirements of V.35.
Unique to the industry, the Sipex's V.35
driver architecture used in the SP505 does
not need external termination resistors to
operate and comply with V.35. This simpli-
fies existing V.35 implementations that use
external termination schemes. The V.35
drivers can produce +0.55V driver output
signals with minimum deviation (maximum
20%) given an equivalent load of 00.
With the help of internal resistor networks,
the drivers achieve the 50 to 50 source
impedance and the 35 to 65 short-cir-
cuit impedance for V.35. The V.35 driver is
disabled and transparent when the decoder
is in all other modes. All of the differential
drivers;V.(RS-422)andV.35,canoperate
over 0Mbps.
Driver Enable and Input
AllthedriversintheSP505containindividual
enablelineswhichcantri-statethedriverout-
puts when a logic "" is applied. This simpli-
fieshalf-duplexconfigurationsforsomeappli-
cations and also provides simpler DTE/DCE
flexibility with one integrated circuit.
The driver inputs are both TTL or CMOS
compatible. Each driver input should have a
pull-down or pull-up resistor so that the out-
put will be at a defined state. Unused driver
inputs should not be left floating.
Receivers
The SP505 has seven (7) independent re-
ceivers which can be programmed for the
different interface modes. Control for the
Drivers
The SP505 has seven (7) enhanced in-
dependent drivers. Control for the mode
selection is done via a four–bit control word.
The drivers are prearranged such that for
each mode of operation, the relative posi-
tion and functionality of the drivers are set
up to accommodate the selected interface
mode.As the mode ofthe drivers is changed,
the electrical characteristics will change to
support the requirements of clock, data, and
control line signal levels. Table shows the
mode of each driver in the different interface
modes that can be selected.
There are four basic types of driver circuits
— V.28, V., V.0 and V.35.
V.28 Drivers
TheV.28driversoutputsingle–endedsignals
with a minimum of +5V (with 3k & 2500pF
loading),andcanoperatetoatleast20kbps
under full load. Since the SP505 uses a
charge pump to generate the RS-232 output
rails, the driver outputs will never exceed
+0V. The V.28 drivers are used in RS-232
mode for all signals, and also in V.35 mode
where four (4) drivers are used as the control
line signals (DTR, RTS, LL, and RL).
V.10 Drivers
The V.0 (RS-423) drivers are also single–
endedsignalswhichproduceopencircuitV
OL
and V
OH measurements of +4.0V to +6.0V.
Whenterminatedwitha450loadtoground,
the driver output will not deviate more than
0% of the open circuit value. This is in
compliance of the ITU V.10 specification.
The V.0 drivers are used in RS-449, EIA-
530, EIA-530Aand V.36 modes as Category
II signals from each of their corresponding
specifications.
V.11 Drivers
The third type of driver is a V. (RS-422)
type differential driver. Due to the nature of
differential signaling, the drivers are more
immunetonoiseasopposedtosingle-ended
transmissionmethods. Theadvantageisevi-
dentoverhighspeedsandlongtransmission
lines. The strength of the driver outputs can
producedifferentialsignalsthatcanmaintain
typically +2.2V differential output levels with
相關PDF資料 |
PDF描述 |
|---|---|
| VE-2TH-IW-F2 | CONVERTER MOD DC/DC 52V 100W |
| MAX1241BESA+ | IC ADC 12BIT SERIAL 8-SOIC |
| MS3102E20-18S | CONN RCPT 9POS BOX MNT W/SCKT |
| MAX1421ECM+D | IC ADC 12BIT 40MSPS 48LQFP |
| LTC1343CGW#PBF | IC TXRX SOFTWARE-SELECTBL 44SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP505AN | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Multi-Protocol Serial Transceivers |
| SP505BCF | 制造商:Exar Corporation 功能描述:Line Transceiver, 7-Driver, 7-Receiver, 80 Pin, Plastic, QFP |
| SP505BCM | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:WAN Multi-Mode Serial Transceiver |
| SP505BCM-L | 功能描述:總線收發器 WAN Multi-Mode Serial RoHS:否 制造商:Fairchild Semiconductor 邏輯類型:CMOS 邏輯系列:74VCX 每芯片的通道數量:16 輸入電平:CMOS 輸出電平:CMOS 輸出類型:3-State 高電平輸出電流:- 24 mA 低電平輸出電流:24 mA 傳播延遲時間:6.2 ns 電源電壓-最大:2.7 V, 3.6 V 電源電壓-最小:1.65 V, 2.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-48 封裝:Reel |
| SP505CF | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Multi-Protocol Serial Transceivers |
發布緊急采購，3分鐘左右您將得到回復。