- 您現在的位置：買賣IC網 > PDF目錄1968 > SP208EHET-L/TR (Exar Corporation)IC TXRX RS232 ESD HP 24SOIC PDF資料下載
參數資料
| 型號： | SP208EHET-L/TR |
| 廠商： | Exar Corporation |
| 文件頁數： | 3/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX RS232 ESD HP 24SOIC |
| 產品變化通告： | Interface Product Discontinuation 10/May/2011 |
| 標準包裝： | 1,500 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 4/4 |
| 規程： | RS232 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 24-SOIC W |
| 包裝： | 帶卷 (TR) |
Exar Corporation 48720 Kato Road, Fremont CA, 94538 50-668-707 www.exar.com
SP2EH_23EH_0_060
RS and RV add up to 330 for IEC61000-4-2.
RC
Device
Under
Test
DC Power
Source
CS
RS
SW1
SW2
RV
Contact-Discharge Model
Figure . ESD Test Circuit for IEC6000-4-2
Figure12.ESDTestWaveformforIEC61000-4-2
The Contact Discharge Method applies the
ESDcurrentdirectlytotheEUT.Thismethod
was devised to reduce the unpredictability
of the ESD arc. The discharge current rise
time is constant since the energy is directly
transferred without the air-gap arc. In situa-
tions such as hand held systems, the ESD
charge can be directly discharged to the
equipment from a person already holding
the equipment. The current is transferred
on to the keypad or the serial port of the
equipment directly and then travels through
thePCBandfinallytotheIC.
The circuit model in Figures 0 and repre-
sent the typical ESD testing circuit used for
all three methods. The C
S is initially charged
with the DC power supply when the first
switch(SW1)ison.Nowthatthecapacitor
ischarged,thesecondswitch(SW2)ison
whileSW1switchesoff.Thevoltagestored
in the capacitor is then applied through R
S,
the current limiting resistor, onto the device
undertest(DUT).InESDtests,theSW2
switch is pulsed so that the device under
test receives a duration of voltage.
For the Human Body Model, the current
limitingresistor(R
S) and the source capacitor
(C
S)are1.5kΩan100pF,respectively.For
IEC-6000-4-2, the current limiting resistor
(R
S) and the source capacitor (CS)are330Ω
an 50pF, respectively.
The higher C
S value and lower RS value in
the IEC6000-4-2 model are more stringent
than the Human Body Model. The larger
storage capacitor injects a higher voltage
tothetestpointwhenSW2isswitchedon.
The lower current limiting resistor increases
the current charge onto the test point.
t=0ns
t=30ns
0A
5A
30A
t
相關PDF資料 |
PDF描述 |
|---|---|
| SP2209EEY-L | IC TXRX RS232 DUAL PORT 38TSSOP |
| SP232AEP-L | IC DVR/RCVR RS232 LP 16PDIP |
| SP233ACP-L | IC DVR/RCVR RS232 ESD 20PDIP |
| SP238ACT-L | IC DVR/RCVR RS232 MULTI 24WSOIC |
| SP26LV431CN-L/TR | IC DVR RS422 QUAD DIFF 16NSOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP208EP | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:+5V High-Speed RS-232 Transceivers with 0.1mF Capacitors |
| SP208EP-L | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| SP208ET | 功能描述:RS-232接口集成電路 RS232 Transceiver 5V 4-driver/4-receiver RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| SP208ET/TR | 功能描述:RS-232接口集成電路 RS232 Transceiver 5V 4-driver/4-receiver RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| SP208ET-L | 功能描述:RS-232接口集成電路 5V 4-DRVR/4-RCVR RS-232 -40-85C RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
發布緊急采購，3分鐘左右您將得到回復。