- 您現在的位置：買賣IC網 > PDF目錄98128 > SN74LVTH652DWRG4 (TEXAS INSTRUMENTS INC) LVT SERIES, 8-BIT REGISTERED TRANSCEIVER, TRUE OUTPUT, PDSO24 PDF資料下載
參數資料
| 型號： | SN74LVTH652DWRG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 總線收發器 |
| 英文描述： | LVT SERIES, 8-BIT REGISTERED TRANSCEIVER, TRUE OUTPUT, PDSO24 |
| 封裝： | GREEN, PLASTIC, SOIC-24 |
| 文件頁數： | 11/18頁 |
| 文件大?。?/td> | 517K |
| 代理商： | SN74LVTH652DWRG4 |
SN54LVTH652, SN74LVTH652
3.3V ABT OCTAL BUS TRANSCEIVERS AND REGISTERS
WITH 3STATE OUTPUTS
SCBS706F AUGUST 1997 REVISED OCTOBER 2003
2
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
description/ordering information (continued)
The ’LVTH652 devices consist of bus-transceiver circuits, D-type flip-flops, and control circuitry arranged for
multiplexed transmission of data directly from the data bus or from the internal storage registers.
Output-enable (OEAB and OEBA) inputs are provided to control the transceiver functions. Select-control (SAB
and SBA) inputs are provided to select whether real-time or stored data is transferred. The circuitry used for
select control eliminates the typical decoding glitch that occurs in a multiplexer during the transition between
real-time and stored data. A low input selects real-time data and a high input selects stored data. Figure 1
illustrates the four fundamental bus-management functions that can be performed with the ’LVTH652 devices.
Data on the A or B data bus, or both, can be stored in the internal D-type flip-flops by low-to-high transitions at
the appropriate clock (CLKAB or CLKBA) inputs, regardless of the select- or enable-control pins. When SAB
and SBA are in the real-time transfer mode, it is possible to store data without using the internal D-type flip-flops
by simultaneously enabling OEAB and OEBA. In this configuration, each output reinforces its input; therefore,
when all other data sources to the two sets of bus lines are at high impedance, each set of bus lines remains
at its last state.
Active bus-hold circuitry is provided to hold unused or floating data inputs at a valid logic level. Use of pullup
or pulldown resistors with the bus-hold circuitry is not recommended.
When VCC is between 0 and 1.5 V, the device is in the high-impedance state during power up or power down.
However, to ensure the high-impedance state above 1.5 V, OE should be tied to VCC through a pullup resistor
and OE should be tied to GND through a pulldown resistor; the minimum value of the resistor is determined by
the current-sinking/current-sourcing capability of the driver.
This device is fully specified for hot-insertion applications using Ioff and power-up 3-state. The Ioff circuitry
disables the outputs, preventing damaging current backflow through the device when it is powered down. The
power-up 3-state circuitry places the outputs in the high-impedance state during power up and power down,
which prevents driver conflict.
FUNCTION TABLE
INPUTS
DATA I/O
OPERATION OR FUNCTION
OEAB
OEBA
CLKAB
CLKBA
SAB
SBA
A1A8
B1B8
OPERATION OR FUNCTION
L
H
H or L
X
Input
Isolation
L
H
↑↑
X
Input
Store A and B data
X
H
↑
H or L
X
Input
Unspecified
Store A, hold B
H
↑↑
X
Input
Output
Store A in both registers
L
X
H or L
↑
X
Unspecified
Input
Hold A, store B
L
↑↑
XX
Output
Input
Store B in both registers
L
X
L
Output
Input
Real-time B data to A bus
L
X
H or L
X
H
Output
Input
Stored B data to A bus
H
X
L
X
Input
Output
Real-time A data to B bus
H
H or L
X
H
X
Input
Output
Stored A data to B bus
H
L
H or L
H
Output
Stored A data to B bus and
stored B data to A bus
The data-output functions can be enabled or disabled by a variety of level combinations at OEAB or OEBA. Data-input functions always are
enabled; i.e., data at the bus terminals is stored on every low-to-high transition of the clock inputs.
Select control = L; clocks can occur simultaneously.
Select control = H; clocks must be staggered to load both registers.
相關PDF資料 |
PDF描述 |
|---|---|
| SN74LVTH652PWG4 | LVT SERIES, 8-BIT REGISTERED TRANSCEIVER, TRUE OUTPUT, PDSO24 |
| SN74LVTH652NSRG4 | LVT SERIES, 8-BIT REGISTERED TRANSCEIVER, TRUE OUTPUT, PDSO24 |
| SN74LVTZ244PWLE | LVT SERIES, DUAL 4-BIT DRIVER, TRUE OUTPUT, PDSO20 |
| SN74LVTZ244DWRG4 | LVT SERIES, DUAL 4-BIT DRIVER, TRUE OUTPUT, PDSO20 |
| SN74LVTZ244DBR | LVT SERIES, DUAL 4-BIT DRIVER, TRUE OUTPUT, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SN74LVTH652IPWREP | 功能描述:總線收發器 Mil Enhance 3.3V ABT Octal Bus Xcvrs RoHS:否 制造商:Fairchild Semiconductor 邏輯類型:CMOS 邏輯系列:74VCX 每芯片的通道數量:16 輸入電平:CMOS 輸出電平:CMOS 輸出類型:3-State 高電平輸出電流:- 24 mA 低電平輸出電流:24 mA 傳播延遲時間:6.2 ns 電源電壓-最大:2.7 V, 3.6 V 電源電壓-最小:1.65 V, 2.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-48 封裝:Reel |
| SN74LVTH652NSR | 功能描述:總線收發器 3.3V ABT Octal Bus Xcvr/Reg RoHS:否 制造商:Fairchild Semiconductor 邏輯類型:CMOS 邏輯系列:74VCX 每芯片的通道數量:16 輸入電平:CMOS 輸出電平:CMOS 輸出類型:3-State 高電平輸出電流:- 24 mA 低電平輸出電流:24 mA 傳播延遲時間:6.2 ns 電源電壓-最大:2.7 V, 3.6 V 電源電壓-最小:1.65 V, 2.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-48 封裝:Reel |
| SN74LVTH652NSRE4 | 功能描述:總線收發器 3.3V ABT Octal Bus Xcvr/Reg RoHS:否 制造商:Fairchild Semiconductor 邏輯類型:CMOS 邏輯系列:74VCX 每芯片的通道數量:16 輸入電平:CMOS 輸出電平:CMOS 輸出類型:3-State 高電平輸出電流:- 24 mA 低電平輸出電流:24 mA 傳播延遲時間:6.2 ns 電源電壓-最大:2.7 V, 3.6 V 電源電壓-最小:1.65 V, 2.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-48 封裝:Reel |
| SN74LVTH652NSRG4 | 功能描述:總線收發器 3.3V ABT Octal Bus Transceiver Register RoHS:否 制造商:Fairchild Semiconductor 邏輯類型:CMOS 邏輯系列:74VCX 每芯片的通道數量:16 輸入電平:CMOS 輸出電平:CMOS 輸出類型:3-State 高電平輸出電流:- 24 mA 低電平輸出電流:24 mA 傳播延遲時間:6.2 ns 電源電壓-最大:2.7 V, 3.6 V 電源電壓-最小:1.65 V, 2.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-48 封裝:Reel |
| SN74LVTH652PW | 功能描述:總線收發器 3.3V ABT Octal Bus Xcvr/Reg RoHS:否 制造商:Fairchild Semiconductor 邏輯類型:CMOS 邏輯系列:74VCX 每芯片的通道數量:16 輸入電平:CMOS 輸出電平:CMOS 輸出類型:3-State 高電平輸出電流:- 24 mA 低電平輸出電流:24 mA 傳播延遲時間:6.2 ns 電源電壓-最大:2.7 V, 3.6 V 電源電壓-最小:1.65 V, 2.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。