參數資料
型號: SN74AHCT123APWLE
廠商: TEXAS INSTRUMENTS INC
元件分類: 諧振器
英文描述: AHCT/VHCT SERIES, DUAL MONOSTABLE MULTIVIBRATOR, PDSO16
封裝: PLASTIC, TSSOP-16
文件頁數: 15/16頁
文件大?。?/td> 216K
代理商: SN74AHCT123APWLE
SN54AHCT123A, SN74AHCT123A
DUAL RETRIGGERABLE MONOSTABLE MULTIVIBRATORS
SCLS420E – JUNE 1998 – REVISED AUGUST 2000
8
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
caution in use
To prevent malfunctions due to noise, connect a high-frequency capacitor between VCC and GND, and keep
the wiring between the external components and Cext and Rext/Cext terminals as short as possible.
power-down considerations
Large values of Cext may cause problems when powering down the ’AHCT123A because of the amount of
energy stored in the capacitor. When a system containing this device is powered down, the capacitor may
discharge from VCC through the protection diodes at pin 2 or pin 14. Current through the input protection diodes
must be limited to 30 mA; therefore, the turn-off time of the VCC power supply must not be faster than
t = VCC × Cext/30 mA. For example, if VCC = 5 V and Cext = 15 pF, the VCC supply must turn off no faster than
t = (5 V)
× (15 pF)/30mA = 2.5 ns. Usually, this is not a problem because power supplies are heavily filtered and
cannot discharge at this rate. When a more rapid decrease of VCC to zero occurs, the ’AHCT123A may sustain
damage. To avoid this possibility, use external clamping diodes.
output pulse duration
The output pulse duration, tw, is determined primarily by the values of the external capacitance (CT) and timing
resistance (RT). The timing components are connected as shown in Figure 2.
VCC
RT
CT
To Rext/Cext
Terminal
To Cext
Terminal
Figure 2. Timing-Component Connections
The pulse duration is given by:
tw
+ K
R
T
C
T
if CT is ≥ 1000 pF, K = 1.0 or
if CT is < 1000 pF, K can be determined from Figure 5
where:
tw = pulse duration in ns
RT = external timing resistance in k
CT = external capacitance in pF
K
= multiplier factor
Equation 1 and Figure 3 can be used to determine values for pulse duration, external resistance, and external
capacitance.
(1)
相關PDF資料
PDF描述
SN74AHCT125DGVRE4 AHCT/VHCT/VT SERIES, QUAD 1-BIT DRIVER, TRUE OUTPUT, PDSO14
SN74AHCT125DBR AHCT/VHCT/VT SERIES, QUAD 1-BIT DRIVER, TRUE OUTPUT, PDSO14
SN74AHCT125PWR AHCT/VHCT/VT SERIES, QUAD 1-BIT DRIVER, TRUE OUTPUT, PDSO14
SN74AHCT125PW AHCT/VHCT/VT SERIES, QUAD 1-BIT DRIVER, TRUE OUTPUT, PDSO14
SN74AHCT125QDRQ1 AHCT/VHCT/VT SERIES, QUAD 4-BIT DRIVER, TRUE OUTPUT, PDSO14
相關代理商/技術參數
參數描述
SN74AHCT123APWR 功能描述:單穩態多諧振蕩器 Dual Retrig Mono RoHS:否 制造商:Texas Instruments 每芯片元件:1 邏輯系列:LVC 邏輯類型:Monostable Multivibrator 封裝 / 箱體:SSOP-8 傳播延遲時間:18.6 ns 高電平輸出電流:- 32 mA 低電平輸出電流:32 mA 電源電壓-最大:5.5 V 電源電壓-最小:1.65 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel
SN74AHCT123APWRE4 功能描述:單穩態多諧振蕩器 Dual retrig monostbl multivibrators RoHS:否 制造商:Texas Instruments 每芯片元件:1 邏輯系列:LVC 邏輯類型:Monostable Multivibrator 封裝 / 箱體:SSOP-8 傳播延遲時間:18.6 ns 高電平輸出電流:- 32 mA 低電平輸出電流:32 mA 電源電壓-最大:5.5 V 電源電壓-最小:1.65 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel
SN74AHCT123APWRG4 功能描述:單穩態多諧振蕩器 Dual Retriggerable Mono Multivibratr RoHS:否 制造商:Texas Instruments 每芯片元件:1 邏輯系列:LVC 邏輯類型:Monostable Multivibrator 封裝 / 箱體:SSOP-8 傳播延遲時間:18.6 ns 高電平輸出電流:- 32 mA 低電平輸出電流:32 mA 電源電壓-最大:5.5 V 電源電壓-最小:1.65 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel
SN74AHCT125D 功能描述:緩沖器和線路驅動器 Tri-State Quad Bus RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel
SN74AHCT125DBR 功能描述:緩沖器和線路驅動器 Tri-State Quad Bus RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel