- 您現在的位置：買賣IC網 > PDF目錄384923 > SMM465FCR03 (Summit Microelectronics, Inc.) 4-Channel Active DC Output Controller, Monitor, Marginer and Sequencer PDF資料下載
參數資料
| 型號： | SMM465FCR03 |
| 廠商： | Summit Microelectronics, Inc. |
| 英文描述： | 4-Channel Active DC Output Controller, Monitor, Marginer and Sequencer |
| 中文描述： | 4通道有源直流輸出控制器，監視器，Marginer和音序器 |
| 文件頁數： | 23/30頁 |
| 文件大?。?/td> | 957K |
| 代理商： | SMM465FCR03 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
SMM465
Preliminary Information
Summit Microelectronics, Inc
2085 1.1 05/27/04
23
WRITE PROTECTION
The SMM465 powers up into a write protected mode.
Writing a code to the volatile write protection register
can disable the write protection. The write protection
register is located at address 87
HEX
of slave address
1001
BIN
.
Writing 0101
BIN
to bits [7:4] of the write protection
register allow writes to the general-purpose memory
while writing 0101
BIN
to bits [3:0] allow writes to the
configuration registers. The write protection can re-
enable by writing other codes (not 0101
BIN
) to the write
protection register. Writing to the write protection
register is shown in Figure 16.
CONFIGURATION REGISTERS
The majority of the configuration registers are grouped
with the general-purpose memory located at either
slave address 1010
BIN
or 1011
BIN
. The bus address
bits, A[1:0], used to differentiate the general-purpose
memory from the configuration registers are set to
11
BIN
. Bus address bit A[2] can be programmed as
either 0 or biased by the A2 pin.
Two additional configuration registers are located at
addresses 83
HEX
and 84
HEX
of slave address 1001
BIN
.
Writing and reading the configuration registers is
shown in Figures 17, 18, 19, 20 and 21
Note: Configuration writes or reads of registers 00
HEX
to 0F
HEX
should not be performed while the SMM465 is
margining.
GENERAL-PURPOSE MEMORY
The 4k-bit general-purpose memory is located at
either slave address 1010
BIN
or 1011
BIN
. The bus
address bits, A[1:0], used to differentiate the general-
purpose memory from the configuration registers are
set to 00
BIN
for the first 2k-bits and 01
BIN
for the second
2k-bits. Bus address bit A[2] can be programmed as
either 0 or biased by the A2 pin.
The word address must be set each time the memory
is accessed. Memory writes and reads are shown in
Figures 22, 23 and 24.
COMMAND AND STATUS REGISTERS
The command and status registers are located at
slave address 1001
BIN
. Writes and reads of the
command and status registers are shown in Figures
25 and 26.
ADC CONVERSIONS
An ADC conversion on any monitored channel can be
performed and read over the I
2
C bus using the ADC
read command. The ADC read command, shown in
Figure 27, starts with a dummy write to the 1001
BIN
slave address. Bits [6:3] of the word address byte are
used to address the desired monitored input. Once
the device acknowledges the channel address, it
begins the ADC conversion of the addressed input.
This conversion requires 70
μ
s to complete. During
this conversion time, acknowledge polling can be
used. The SMM465 will not acknowledge the address
bytes until the conversion is complete. When the
conversion
has
completed,
acknowledge the address byte and return the 10-bit
conversion along with a 4-bit channel address echo.
GRAPHICAL USER INTERFACE (GUI)
Device configuration utilizing the Windows based
SMM465 graphical user interface (GUI) is highly
recommended. The software is available from the
Summit website (
www.summitmicro.com
). Using the
GUI in conjunction with this datasheet and Application
Note 33, simplifies the process of device prototyping
and the interaction of the various functional blocks. A
programming Dongle (SMX3200) is available from
Summit to communicate with the SMM465. The
Dongle connects directly to the parallel port of a PC
and programs the device through a cable using the I
2
C
bus protocol.
Register Type
the
SMM465
will
Slave Address Bus Address
1001
BIN
A2 A1 A0
Write Protection Register,
Command and Status Registers,
Two Configuration Registers,
ADC Conversion Readout
A2 0 0
1
st
2-k Bits of General-Purpose Memory
2
nd
2-k Bits of General-Purpose Memory
A2 0 1
1010
BIN
or
1011
BIN
A2 1 1
Configuration Registers
Table 1 - Address bytes used by the SMM465.
I
2
C PROGRAMMING INFORMATION (CONTINUED)
相關PDF資料 |
PDF描述 |
|---|---|
| SMM465FCR04 | 4-Channel Active DC Output Controller, Monitor, Marginer and Sequencer |
| SMM465FCR05 | 4-Channel Active DC Output Controller, Monitor, Marginer and Sequencer |
| SMM465FR00 | 4-Channel Active DC Output Controller, Monitor, Marginer and Sequencer |
| SMM465FR01 | 4-Channel Active DC Output Controller, Monitor, Marginer and Sequencer |
| SMM465FR02 | 4-Channel Active DC Output Controller, Monitor, Marginer and Sequencer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SMM465FCR04 | 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:4-Channel Active DC Output Controller, Monitor, Marginer and Sequencer |
| SMM465FCR05 | 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:4-Channel Active DC Output Controller, Monitor, Marginer and Sequencer |
| SMM465FR00 | 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:4-Channel Active DC Output Controller, Monitor, Marginer and Sequencer |
| SMM465FR01 | 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:4-Channel Active DC Output Controller, Monitor, Marginer and Sequencer |
| SMM465FR02 | 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:4-Channel Active DC Output Controller, Monitor, Marginer and Sequencer |
發布緊急采購，3分鐘左右您將得到回復。