參數資料
型號： SMH4814SCR00
廠商： Summit Microelectronics, Inc.
元件分類： 基準電壓源/電流源
英文描述： Dual Feed Active-ORing Programmable Hot Swap Controller
中文描述： 雙飼料有源ORing提供可編程熱插拔控制器
文件頁數： 4/44頁
文件大?。?/td> 935K
代理商： SMH4814SCR00
SMH4814
Preliminary Information
Summit Microelectronics, Inc
2080 2.0 07/21/05
4
PIN DESCRIPTION
Pin No.
QFN
Pin Type
Name
Description
1,2
I
PD0, PD1
The PD pins are active high, logic level inputs. Protection diodes allow
them to be overdriven when used in conjunction with a series limiting
resistor. The PD pins have an internal pull-down current sink of 10uA
typical.
The RESET# pin is used to clear latched fault conditions. When this pin is
asserted, the VGATE
X
and PUP
X
outputs are immediately disabled. Refer to
the section on Circuit Breaker Operation for more information. The RESET#
pin has an internal pull-up current source to 5V_CAP of 10uA typical.
SCL is the serial clock input.
3
I
RESET#
4
I
SCL
5
I/O
SDA
SDA is the bidirectional serial data I/O port.
The PUP
X
outputs are programmable active high/low open drain converter
enable pins. They can be used in one of 4 programmable sequence
positions to switch a load or enable a DC/DC converter after a
programmable delay, t
PGDn
. The voltage on these pins cannot exceed 12V
relative to V
SS
.
FAULT# is an open-drain, active-low output that indicates the fault status of
the device. The device’s Status Register may be polled to determine more
detailed information about the fault condition.
This is connected to the negative side of the supply.
6,
7,
8,
9
O
PUP
A
, PUP
B
,
PUP
C
,
PUP
D
10
O
FAULT#
11
PWR
VSS
12
I
CBSENSE
The circuit breaker sense input is used to detect over-current conditions
across an external, low value sense resistor (R
S
)
tied in series with the
Power MOSFET. A voltage drop of greater than V
CB
(programmable level)
across the resistor for longer than t
CBD
trips the circuit breaker. A
programmable Quick-Trip sense point is also available.
The UV pin is used as an under-voltage supply monitor, typically in
conjunction with an external resistor ladder. VGATE_HS is enabled when
the UV input > Vuv and disabled when UV < Vuv-Vuvhys. An optional
programmable filter delay is also available on the UV input.
The OV pin is used as an over-voltage supply monitor, typically in
conjunction with an external resistor ladder. VGATE_HS is disabled when
OV > Vov and enabled when OV < Vov-Vovhys. A filter delay is also
available on the OV input.
13
I
UV
14
I
OV
15
I
EN/TS
The Enable/Temperature Sense input is the master enable input. If EN/TS
is less than 2.5V, all VGATE outputs are disabled.
A capacitor connected to this pin controls the VGATE_HS Slew Rate.
16
I
SLEW_CNTL
17
I
FEED
B
Connect to the -48V 'B' feed using a series 100k resistor. The voltage on
this pin is compared with the voltage on the FEED
A
pin internally by the
supply arbitration logic to determine which voltage will be used.
相關PDF資料
PDF描述
SMH4814SCR01 Dual Feed Active-ORing Programmable Hot Swap Controller
SMH4814SCR02 Dual Feed Active-ORing Programmable Hot Swap Controller
SMH4814SCR03 Dual Feed Active-ORing Programmable Hot Swap Controller
SMH4814SCR04 Dual Feed Active-ORing Programmable Hot Swap Controller
SMH4814SCR05 Dual Feed Active-ORing Programmable Hot Swap Controller
相關代理商/技術參數
參數描述
SMH4814SCR01 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Dual Feed Active-ORing Programmable Hot Swap Controller
SMH4814SCR02 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Dual Feed Active-ORing Programmable Hot Swap Controller
SMH4814SCR03 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Dual Feed Active-ORing Programmable Hot Swap Controller
SMH4814SCR04 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Dual Feed Active-ORing Programmable Hot Swap Controller
SMH4814SCR05 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Dual Feed Active-ORing Programmable Hot Swap Controller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*