參數資料
型號： SMH4814NR05
廠商： Summit Microelectronics, Inc.
元件分類： 基準電壓源/電流源
英文描述： Dual Feed Active-ORing Programmable Hot Swap Controller
中文描述： 雙飼料有源ORing提供可編程熱插拔控制器
文件頁數： 17/44頁
文件大?。?/td> 935K
代理商： SMH4814NR05
SMH4814
Preliminary Information
Summit Microelectronics, Inc
2080 2.0 07/21/05
17
Circuit Breaker Operation
The SMH4814 provides a highly configurable method
for detecting and controlling over-current events. A
sustained over-current condition can cause physical
damage to the card edge connector, the load circuitry,
and may even disrupt operation of other cards in the
system. To detect such over-current conditions, a
series sense resistor (R
S
) is connected between the
MOSFET source (which is tied to CBSENSE) and V
SS
.
The board’s load current passes through the sense
resistor, and the CBSENSE input is monitored for
excessive voltage drop across R
S
.
The SMH4814 compares the CBSENSE input against
three important voltage levels (V
CB
, V
QCB
, and V
CR
) and
takes appropriate action as each successive level is
reached. The first voltage, V
CB
, is the circuit breaker
trip point, which is determined by R0A[7:0]. V
CB
may
be set to any one of 256 levels up to a maximum
voltage of V
CBMAX
, which is a configurable voltage of
128mV, 256mV, 512mV or 1024mV, as determined by
R09[5:4]. For example, if V
CBMAX
is set to 256mV, then
V
CB
may be programmed to any value between 0 and
255mV, in 1mV increments. (Refer to the Register
Description for more information.) If CBSENSE
exceeds V
CB
for a period of time longer than the glitch
filter delay associated with that input, t
CBD
(set using
R06[1:0]), then the device is considered to be in an
over-current state. Once in an over-current state, the
SMH4814 will either shut down immediately, or if the
Current Regulation option is selected (R05[3]), the
device will begin another timer. Refer to the
description of Current Regulation for more information
on these actions.
Quick-Trip
TM
The second voltage level that the CBSENSE input is
compared against is the Quick-Trip Circuit Breaker
level, V
QCB
. V
QCB
is determined by the contents of
R0B[7:0], in a manner similar to V
CB
. (Note that the
value stored in R0B is a 2’s complement number; refer
to the Register Description for more information.)
Unlike the V
CB
comparator, the output of the V
QCB
comparator is a high-speed, non-filtered signal
designed to shutdown the MOSFET gate very quickly.
If the Current Regulation option is not selected, then
exceeding the Quick-Trip level causes an immediate
shutdown of the PUP outputs and MOSFET gate;
however, if Current Regulation is selected, the PUP
outputs will not be immediately shut off. Refer to the
description of Current Regulation for more information.
Circuit Breaker
Figure 10 shows the circuit breaker ‘Quick Trip’
response. In this figure, the voltage rises above V
QCB
,
causing VGATE to be deasserted.
CBSENSE
VGATE_HS
V
CB
t
QTSD
V
QCB
<t
CBD
Figure 10 - Circuit Breaker Quick Trip Response
without current regulation.
Current Regulation
The Current Regulation mode is an optional feature
that provides a means to regulate current through the
MOSFET for a programmable period of time. This
mode allows the system to “ride out” temporary
disruptions that might otherwise cause traditional
circuit breakers to trip. The Current Regulation trip
point, V
CR
, is the third voltage level against which the
CBSENSE input is compared. V
CR
is determined by
register R09[7:6] and is expressed as a percentage
above the V
CB
level. There are four choices: 12.5%,
25%, 50% and 100%. Note that the Quick-Trip level
V
QCB
should be chosen to fall above V
CR
in order for
Current Regulation to be effective.
Current Regulation works by modulating VGATE_HS
so that CBSENSE is always less than or equal to V
CR
.
In order to avoid overheating the MOSFET by
operating in its linear region for too long, a timer is
started whenever CBSENSE goes above V
CB
or
VGATE_HS falls at least V
GT
below V12. If either of
these conditions exist for the duration of the current
regulation timer, t
CR
, then the PUP and VGATE
outputs are shut down. There are actually two
different Current Regulation timers; R00[7:4] controls
the timing for the initial VGATE_HS turn on, and
R04[7:4] controls the timing for all subsequent current
regulation events.
APPLICATIONS INFORMATION (CONTINUED)
相關PDF資料
PDF描述
SMH4814SCR00 Dual Feed Active-ORing Programmable Hot Swap Controller
SMH4814SCR01 Dual Feed Active-ORing Programmable Hot Swap Controller
SMH4814SCR02 Dual Feed Active-ORing Programmable Hot Swap Controller
SMH4814SCR03 Dual Feed Active-ORing Programmable Hot Swap Controller
SMH4814SCR04 Dual Feed Active-ORing Programmable Hot Swap Controller
相關代理商/技術參數
參數描述
SMH4814SCR00 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Dual Feed Active-ORing Programmable Hot Swap Controller
SMH4814SCR01 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Dual Feed Active-ORing Programmable Hot Swap Controller
SMH4814SCR02 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Dual Feed Active-ORing Programmable Hot Swap Controller
SMH4814SCR03 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Dual Feed Active-ORing Programmable Hot Swap Controller
SMH4814SCR04 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Dual Feed Active-ORing Programmable Hot Swap Controller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*