- 您現在的位置：買賣IC網 > PDF目錄384922 > SMH4814NR01 (Summit Microelectronics, Inc.) Dual Feed Active-ORing Programmable Hot Swap Controller PDF資料下載
參數資料
| 型號： | SMH4814NR01 |
| 廠商： | Summit Microelectronics, Inc. |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Dual Feed Active-ORing Programmable Hot Swap Controller |
| 中文描述： | 雙飼料有源ORing提供可編程熱插拔控制器 |
| 文件頁數： | 13/44頁 |
| 文件大小： | 935K |
| 代理商： | SMH4814NR01 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
SMH4814
Preliminary Information
Summit Microelectronics, Inc
2080 2.0 07/21/05
13
General Purpose EEPROM
The SMH4814 has 256 bytes of general-purpose
EEPROM memory available to the user. These 2k-
bits of EEPROM are accessible via the I
C interface at
slave address 1010 or 1011, beginning at word
address 0 (0x000) and ending at word address 255
(0x0FF). Refer to the I
2
C 2-Wire Serial Interface
section for more information.
Configuration Registers
There are also 20 user-programmable, non-volatile
configuration registers on the SMH4814. The
configuration registers are accessible via the IIC
interface at the same slave address as the general
purpose EEPROM, beginning at word address 256
(0x100) and ending at address 271 (0x113). These
locations will be referred to throughout this document
as registers R00 through R13. Individual bits or
ranges of bits will be further denoted with square
brackets. For example, R00[3:0] refers to Register
0x100, bits 3 through 0. R0D[6,2] refers to Register
0x10D, bits 6 and 2. The configuration registers are
responsible for setting all of the programmable
parameters described within this document. Refer to
the Configuration Register Tables for more detailed
information about all the register settings.
Pin Detection
There are several enabling inputs that allow the host
to control the SMH4814. The Pin Detect signals (PD1
and PD0) are two active high enables that are
generally used to indicate that the add-in circuit card is
properly seated. These inputs must be held high for a
pin-detect delay period of t
PDD
before a power-up
sequence may be initiated. This is typically done by
clamping the inputs to 5v through the implementation
of an ejector switch, or alternatively through the use of
staggered pins at the card-cage interface.
SMH4814
CHASSIS
CARD
-48V Ret
-48V A
-48V B
PD1
PD0
V
1
V
S
Short Pins
100k
100k
R
D
Figure 8 - PD1 and PD0 Inputs, Physical Offset
Two shorter pins, arranged at opposite ends of the
connector, force the card to be fully seated before both
pin detects are enabled. It is important to use limiting
resistors (typically 100k to 1M) in series with the PD
inputs to avoid damaging them. An internal shunt
prevents the voltage on those pins from reaching
unsafe levels.
The PD inputs may be disabled using R0F[2];
however, even if the Pin Detect inputs are disabled or
tied directly to 5V, the device must still wait a pin
detect delay period before starting up. The pin detect
delay (t
PDD
) timing parameter is controlled by bits
R00[3:0]. Refer to Register R00 and R0F for detailed
programming information.
EN/TS Input
The EN/TS input provides an active high comparator
input that may be used as a master enable or
temperature sense input. This input signal must
exceed 2.5V to enable the FET turn-on sequence. If
EN/TS drops below the 2.5V sense level, the device
may be configured to set the FAULT# output or not,
and initiates either a Forced Shutdown or Power Down
sequence. These options are set using R0D[6,2].
APPLICATIONS INFORMATION
相關PDF資料 |
PDF描述 |
|---|---|
| SMH4814NR02 | Dual Feed Active-ORing Programmable Hot Swap Controller |
| SMH4814NR03 | Dual Feed Active-ORing Programmable Hot Swap Controller |
| SMH4814NR04 | Dual Feed Active-ORing Programmable Hot Swap Controller |
| SMH4814NR05 | Dual Feed Active-ORing Programmable Hot Swap Controller |
| SMH4814SCR00 | Dual Feed Active-ORing Programmable Hot Swap Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SMH4814NR02 | 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Dual Feed Active-ORing Programmable Hot Swap Controller |
| SMH4814NR03 | 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Dual Feed Active-ORing Programmable Hot Swap Controller |
| SMH4814NR04 | 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Dual Feed Active-ORing Programmable Hot Swap Controller |
| SMH4814NR05 | 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Dual Feed Active-ORing Programmable Hot Swap Controller |
| SMH4814SCR00 | 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Dual Feed Active-ORing Programmable Hot Swap Controller |
發布緊急采購，3分鐘左右您將得到回復。