參數資料
型號: SMH4812G
廠商: Summit Microelectronics, Inc.
元件分類: 基準電壓源/電流源
英文描述: Distributed Power Hot-Swap Controller
中文描述: 分布式電源熱插拔控制器
文件頁數: 3/19頁
文件大小: 441K
代理商: SMH4812G
3
2055 4.0 12/22/00
SMH4812
Preliminary
SUMMIT MICROELECTRONICS, Inc.
PIN CONFIGURATION
PIN DESCRIPTIONS
DRAIN SENSE (1)
The DRAIN SENSE input monitors the voltage at the drain
of the external power MOSFET switch with respect to V
SS
.
An internal 10μA source pulls the DRAIN SENSE signal
towards the 5V reference level. DRAIN SENSE must be
held below 2.5V to enable the PG outputs.
EN/TS (3)
The Enable/Temperature Sense input is the master en-
able input. If EN/TS is less than 2.5V, VGATE will be
disabled. This pin has an internal 200kW pull-up to 5V.
PD1#, PD2# (4, 5)
These are logic level active low inputs that can optionally
be employed to enable VGATE and the PG outputs when
they are at V
SS
. These pins each have an internal 50kW
pull-up to 5V.
CBSENSE (7)
The circuit breaker sense input is used to detect over-
current conditions across an external, low value sense
resistor (R
S
) tied in series with the Power MOSFET. A
voltage drop of greater than 50mV across the resistor for
longer than t
CBD
will trip the circuit breaker. A program-
mable Quick-Trip sense point is also available.
UV (9)
The UV pin is used as an under-voltage supply monitor,
typically in conjunction with an external resistor ladder.
VGATE will be disabled if UV is less than 2.5V. Program-
mable internal hysteresis is available on the UV input,
adjustable in increments of 62.5mV. Also available is a
filter delay on the UV input.
OV (10)
The OV pin is used as an over-voltage supply monitor,
typically in conjunction with an external resistor ladder.
VGATE will be disabled if OV is greater than 2.5V. A filter
delay is available on the OV input.
VGATE (2)
The VGATE output activates an external power MOSFET
switch. This signal supplies a constant current output
(100μA typical), which allows easy adjustment of the
MOSFET turn on slew rate.
FAULT
#
(6)
FAULT# is an open-drain, active-low output that indicates
the fault status of the device.
5VREF (11)
This is a precision 5V output reference voltage that may be
used to expand the logic input functions on the SMH4812.
The reference output is with respect to V
SS
.
2.5VREF (12)
This is a precision 2.5V output reference voltage that may
be used to expand the logic input functions on the
SMH4812. The reference output is with respect to V
SS
.
FS# (13)
The Forced Shutdown (FS#) pin is an active low input that
causes VGATE and PG outputs to be shut down at any
time after an internal hold-off timer has expired. The hold-
off timer allows supervisory circuits on the secondary side
(which are not powered up initially) to control shut down of
the SMH4812 via an opto-isolator. This input has no pull-
up resistor.
DRAIN SENSE
VGATE
EN/TS
PD1#
PD2#
FAULT#
CBSENSE
V
SS
V
DD
PG#
ENPG
FS#
2.5V
REF
5V
REF
OV
UV
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
2055 PCon 2.0
相關PDF資料
PDF描述
SMH4812S Distributed Power Hot-Swap Controller
SMH4814 Dual Feed Active-ORing Programmable Hot Swap Controller
SMH4814NCR00 Dual Feed Active-ORing Programmable Hot Swap Controller
SMH4814NCR01 Dual Feed Active-ORing Programmable Hot Swap Controller
SMH4814NCR02 Dual Feed Active-ORing Programmable Hot Swap Controller
相關代理商/技術參數
參數描述
SMH4812S 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Distributed Power Hot-Swap Controller
SMH4814 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Dual Feed Active-ORing Programmable Hot Swap Controller
SMH4814NCR00 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Dual Feed Active-ORing Programmable Hot Swap Controller
SMH4814NCR01 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Dual Feed Active-ORing Programmable Hot Swap Controller
SMH4814NCR02 制造商:SUMMIT 制造商全稱:SUMMIT 功能描述:Dual Feed Active-ORing Programmable Hot Swap Controller