- 您現在的位置：買賣IC網 > PDF目錄98082 > SL23EP08SC-2T 23EP SERIES, PLL BASED CLOCK DRIVER, 4 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO16 PDF資料下載
參數資料
| 型號： | SL23EP08SC-2T |
| 元件分類： | 時鐘及定時 |
| 英文描述： | 23EP SERIES, PLL BASED CLOCK DRIVER, 4 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO16 |
| 封裝： | 0.150 INCH, ROHS COMPLIANT,SOIC-16 |
| 文件頁數： | 7/18頁 |
| 文件大小： | 405K |
| 代理商： | SL23EP08SC-2T |
Rev 2.0, May 28, 2008
Page 15 of 18
SL23EP08
(-2, -2H and -3 Versions)
Fout=166MHz and CL=15pF
-
400
ps
PLL Lock Time
tLOCK
From 0.95VDD and valid CLKIN
-
1.0
ms
External Components & Design Considerations
Typical Application Schematic
Comments and Recommendations
Decoupling Capacitor:
A minimum decoupling capacitor of 0.1μF must be used between VDD and VSS pins.
Additional capacitors may be necessary depending on the application. Place the capacitor on the component side of
the PCB as close to the VDD pin as possible. The PCB trace to the VDD pin and to the GND via should be kept as
short as possible. Do not use vias between the decoupling capacitor and the VDD pin.
Series Termination Resistor:
A series termination resistor is recommended if the distance between the output
clocks and the load is over 1 inch. The nominal impedance of the clock outputs is given on the Operating
Conditions Tables. Place the series termination resistors as close to the clock outputs as possible.
Zero Delay and Skew Control:
All outputs and CLKIN pins should be loaded with the same load to achieve “Zero
Delay” between the CLKIN and the outputs. The CLKOUT pin is connected to CLKIN internally on-chip for feedback
to PLL. For applications requiring zero input/output delay, the load at the all output pins including the CLKOUT pin
must be the same. If any delay adjustment is required, the capacitance at the CLKOUT pin could be increased or
decreased to increase or decrease the delay between Bank A and B clocks and CLKIN. For minimum pin-to-pin
skew, the external load at all the Bank A and B clocks must be the same.
相關PDF資料 |
PDF描述 |
|---|---|
| SL23EP08SI-1H | 23EP SERIES, PLL BASED CLOCK DRIVER, 4 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO16 |
| SL23EP08SC-4T | 23EP SERIES, PLL BASED CLOCK DRIVER, 4 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO16 |
| SL23EP08ZI-1 | PLL BASED CLOCK DRIVER, PDSO16 |
| SL23EP08ZI-1HT | 23EP SERIES, PLL BASED CLOCK DRIVER, 4 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO16 |
| SL23EP08SC-4T | 23EP SERIES, PLL BASED CLOCK DRIVER, 4 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SL23EP08SC-3 | 功能描述:時鐘緩沖器 10-220MHz 8 Outputs ZDB 3.3-2.5V RoHS:否 制造商:Texas Instruments 輸出端數量:5 最大輸入頻率:40 MHz 傳播延遲（最大值）: 電源電壓-最大:3.45 V 電源電壓-最小:2.375 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LLP-24 封裝:Reel |
| SL23EP08SC-3T | 功能描述:時鐘緩沖器 10-220MHz 8 Outputs ZDB 3.3-2.5V RoHS:否 制造商:Texas Instruments 輸出端數量:5 最大輸入頻率:40 MHz 傳播延遲（最大值）: 電源電壓-最大:3.45 V 電源電壓-最小:2.375 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LLP-24 封裝:Reel |
| SL23EP08SC-4 | 功能描述:時鐘緩沖器 10-220MHz 8 Outputs ZDB 3.3-2.5V RoHS:否 制造商:Texas Instruments 輸出端數量:5 最大輸入頻率:40 MHz 傳播延遲（最大值）: 電源電壓-最大:3.45 V 電源電壓-最小:2.375 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LLP-24 封裝:Reel |
| SL23EP08SC-4H | 功能描述:時鐘緩沖器 10-220MH 8 Outputs ZDB 3.3-2.5V RoHS:否 制造商:Texas Instruments 輸出端數量:5 最大輸入頻率:40 MHz 傳播延遲（最大值）: 電源電壓-最大:3.45 V 電源電壓-最小:2.375 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LLP-24 封裝:Reel |
| SL23EP08SC-4HT | 功能描述:時鐘緩沖器 10-220MH 8 Output ZDB 3.3-2.5V RoHS:否 制造商:Texas Instruments 輸出端數量:5 最大輸入頻率:40 MHz 傳播延遲（最大值）: 電源電壓-最大:3.45 V 電源電壓-最小:2.375 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LLP-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。