- 您現在的位置：買賣IC網 > PDF目錄98081 > SL2305SC-1HT (SILICON LABORATORIES) 2305 SERIES, PLL BASED CLOCK DRIVER, 4 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO8 PDF資料下載
參數資料
| 型號： | SL2305SC-1HT |
| 廠商： | SILICON LABORATORIES |
| 元件分類： | 時鐘及定時 |
| 英文描述： | 2305 SERIES, PLL BASED CLOCK DRIVER, 4 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO8 |
| 封裝： | 0.150 INCH, ROHS COMPLIANT, SOIC-8 |
| 文件頁數： | 9/11頁 |
| 文件大?。?/td> | 150K |
| 代理商： | SL2305SC-1HT |
Rev 2.1, October 22, 2007
Page 7 of 11
SL2305
External Components & Design Considerations
Typical Application Schematic
SL2305
CL
0.1
μF
CLKIN
CLKOUT
CLK1
CLK4
GND
VDD
1
6
4
7
3
8
Comments and Recommendations
Decoupling Capacitor:
A decoupling capacitor of 0.1μF must be used between VDD and VSS on the pins 6 and 4. Place
the capacitor on the component side of the PCB as close to the VDD pin as possible. The PCB trace to the VDD pin and to
the GND via should be kept as short as possible. Do not use vias between the decoupling capacitor and the VDD pin.
Series Termination Resistor: A series termination resistor is recommended if the distance between the outputs and the
load is over 1 inch. The nominal impedance of the Clock outputs are
about 30 Ω. Use 20 Ω resistor in series with the
output to terminate 50Ω trace impedance and place 20 Ω resistor as close to the clock outputs as possible.
Zero Delay and Skew Control: All outputs and CLKIN pins should be loaded with the same load to achieve “Zero Delay”
between the CLKIN and the outputs. The CLKOUT pin is connected to CLKIN internally on-chip for internal feedback to
PLL, and sees an additional 2 pF load with respect to the clock pins. For applications requiring zero input/output delay, the
load at the all output pins including the CLKOUT pin must be the same. If any delay adjustment is required, the capacitance
at the CLKOUT pin could be increased or decreased to increase or decrease the delay between clocks and CLKIN.
For minimum pin-to-pin skew, the external load at the clock outputs must be the same.
相關PDF資料 |
PDF描述 |
|---|---|
| SL2305SC-1H | 2305 SERIES, PLL BASED CLOCK DRIVER, 4 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO8 |
| SL2305ZC-1H | 2305 SERIES, PLL BASED CLOCK DRIVER, 4 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO8 |
| SL2305SC-1H | 2305 SERIES, PLL BASED CLOCK DRIVER, 4 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO8 |
| SL2305SI-1T | 2305 SERIES, PLL BASED CLOCK DRIVER, 4 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO8 |
| SL2305ZC-1T | 2305 SERIES, PLL BASED CLOCK DRIVER, 4 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SL2305SC-1T | 功能描述:時鐘緩沖器 10-140MHz 5 Outputs ZDB 3.3V RoHS:否 制造商:Texas Instruments 輸出端數量:5 最大輸入頻率:40 MHz 傳播延遲（最大值）: 電源電壓-最大:3.45 V 電源電壓-最小:2.375 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LLP-24 封裝:Reel |
| SL2305SI-1 | 功能描述:時鐘緩沖器 10-140MHz 5 Outputs ZDB 3.3V RoHS:否 制造商:Texas Instruments 輸出端數量:5 最大輸入頻率:40 MHz 傳播延遲（最大值）: 電源電壓-最大:3.45 V 電源電壓-最小:2.375 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LLP-24 封裝:Reel |
| SL2305SI-1H | 功能描述:時鐘緩沖器 10-140MHz 5 Outputs ZDB 3.3V High Drive RoHS:否 制造商:Texas Instruments 輸出端數量:5 最大輸入頻率:40 MHz 傳播延遲（最大值）: 電源電壓-最大:3.45 V 電源電壓-最小:2.375 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LLP-24 封裝:Reel |
| SL2305SI-1HT | 功能描述:時鐘緩沖器 10-140MHz 5 Outputs ZDB 3.3V High Drive RoHS:否 制造商:Texas Instruments 輸出端數量:5 最大輸入頻率:40 MHz 傳播延遲（最大值）: 電源電壓-最大:3.45 V 電源電壓-最小:2.375 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LLP-24 封裝:Reel |
| SL2305SI-1T | 功能描述:時鐘緩沖器 10-140MHz 5 Outputs ZDB 3.3V RoHS:否 制造商:Texas Instruments 輸出端數量:5 最大輸入頻率:40 MHz 傳播延遲（最大值）: 電源電壓-最大:3.45 V 電源電壓-最小:2.375 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LLP-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。