參數資料
型號: SL2150LH2S
廠商: Zarlink Semiconductor Inc.
英文描述: Front End Power Splitter with AGC
中文描述: 功分器前端具有AGC
文件頁數: 13/20頁
文件大?。?/td> 942K
代理商: SL2150LH2S
Data Sheet
SL2150F
13
SEMICMF.019
4.0
SL2150F Demonstration Board
The SL2150F demonstration board is designed to allow testing of device functionality as a stand alone power
splitter. It allows for testing of the AGC function and independent testing of all channels.
The SL2150F is designed to interface differentially into a silicon tuner such as the SL2101 with simple inductive or
resistive pull-ups. However, to facilitate testing the differential, output is converted to a single ended signal through
a balun. The differential conversion is necessary for achieving second order performance.
All outputs require a DC return path to Vcc to prevent output saturation. This can be provided by the balun, inductive
pull up or resistive pull up. In the case of a resistive pull up, the maximum load value is 38
.
The balun also provides the DC bias to the outputs; all outputs have to be DC 'shorted' to Vcc to prevent saturation
of the output stages.
All input and output terminations are 75
.
The board schematic and layout are contained in Figure 19 - "Test Board Schematic" and Figure 20 - "Test Board
Layout" respectively.
Operation note
The supply voltage must be connected and enabled before any AGC voltage is applied unless the AGC
supplies are current limited to <1 mA or else permanent damage may occur through the ESD structures on
the device.
4.1
Pin Connections
All references are with the board oriented as in bottom view on Figure 1 - "SL2150F Block Diagram". Pin 1 of the
header is defined as the left-hand pin.
4.2
Power Supply
A single 5V supply is required. Power is supplied through the two-pin header PL1, located top right hand corner.
4.3
RF Input
The RF input F type, SK1, is located on the right hand side of the board.
4.4
RF Outputs
Output 1 is the upper of the two F type connectors, SK3, located on the left-hand side.
Output 2 is the lower of the two F type connector, SK4, located on the left-hand side.
Output 3 is the F type connector, SK5, located at the bottom of the board
Output 4 is the F type connector, SK2, located at the top of the board.
Pin
Function
1
Vcc
2
Vee
相關PDF資料
PDF描述
SL2150KG Cable Tuner Front End LNA with AGC
SL2150D Cable Tuner Front End LNA with AGC
SL2150LH1S Cable Tuner Front End LNA with AGC
SL2150LH2R Cable Tuner Front End LNA with AGC
SL2150LH2T Cable Tuner Front End LNA with AGC
相關代理商/技術參數
參數描述
SL2150LH2T 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Cable Tuner Front End LNA with AGC
SL215-3-1 制造商:SHUR-LOK 功能描述:
SL215A102KAB 功能描述:多層陶瓷電容器MLCC - 含引線 50volts 1000pF 10% C0G RoHS:否 制造商:AVX 電容:470 pF 容差:10 % 電壓額定值:3 kV 端接類型:Radial 工作溫度范圍: 溫度系數/代碼:X7R 引線間隔:5.08 mm 產品:Automotive MLCCs 引線類型:
SL215A151JAB 功能描述:多層陶瓷電容器MLCC - 含引線 50volts 150pF 5% C0G RoHS:否 制造商:AVX 電容:470 pF 容差:10 % 電壓額定值:3 kV 端接類型:Radial 工作溫度范圍: 溫度系數/代碼:X7R 引線間隔:5.08 mm 產品:Automotive MLCCs 引線類型:
SL215A180JAB 功能描述:多層陶瓷電容器MLCC - 含引線 50volts 18pF 5% C0G RoHS:否 制造商:AVX 電容:470 pF 容差:10 % 電壓額定值:3 kV 端接類型:Radial 工作溫度范圍: 溫度系數/代碼:X7R 引線間隔:5.08 mm 產品:Automotive MLCCs 引線類型: