- 您現在的位置：買賣IC網 > PDF目錄374804 > SL2150LH1S (Zarlink Semiconductor Inc.) Cable Tuner Front End LNA with AGC PDF資料下載
參數資料
| 型號： | SL2150LH1S |
| 廠商： | Zarlink Semiconductor Inc. |
| 英文描述： | Cable Tuner Front End LNA with AGC |
| 中文描述： | 有線電視調諧器前端低噪聲放大器的自動增益控制 |
| 文件頁數： | 3/16頁 |
| 文件大?。?/td> | 319K |
| 代理商： | SL2150LH1S |
SL2150D
Data Sheet
3
Zarlink Semiconductor Inc.
2.0 Functional Description
The SL2150D is a broadband wide dynamic range dual output tuner front end LNA with AGC. It also has application
is any system where a wide dynamic range broadband power splitter is required.
The pin assignment is contained in Figure 2 and the block diagram in Figure 1.The port internal peripheral circuits
are contained in Figure 14.
In normal application the RF input is interfaced to the device input. The input preamplifier is designed for low noise
figure, within the operating region of 50 to 860 MHz and for high intermodulation distortion intercept so offering
good signal to noise plus composite distortion spurious performance when loaded with a multi carrier system. The
preamplifier also provides an impedance match to a 75
source; the typical impedance is shown in Figure 4.
The input NF is shown in Figure 6.
The output of the preamplifier is then power split to two independently controlled AGC stages. Each AGC stage
provides for a minimum of 30 dB of gain control across the input frequency range. The typical AGC characteristic
and NF versus gain setting are contained in Figure 5 and Figure 7 respectively.
Finally each of the AGC stages drive an output buffer of differential output impedance of 440
, which provides a
nominal 11 dB of gain when terminated into a differential 75
load, as in Figure 11. Each channel AGC and output
buffer can be independently powered down.
In application it is important to avoid saturation of the output stage, therefore it is recommended that the output
standing current be sunk to Vcc through an inductor. A resistive pull up can also be used as shown in Figure 13 -
"Example Application Driving 100 W Load with Resistive Pull Up", however the resistor values should not exceed
20 ohm single ended.
If an inductive current sink is used the maximum available gain from the device is circa 26 dB. This gain can be
reduced by application of an external load between the differential output ports. The gain can be approximately
calculated from the following formula:
- GAIN = 20*log ((Parallel combination of 440 ohm and external load between ports)/22 ohm)+2 dB
For example when driving a 100 ohm load as in Figure 12, the gain equals
- GAIN = 20 *log ((440 *100)/(440+100)/22)+2 dB =12 dB.
相關PDF資料 |
PDF描述 |
|---|---|
| SL2150LH2R | Cable Tuner Front End LNA with AGC |
| SL2150LH2T | Cable Tuner Front End LNA with AGC |
| SL24T1 | 300 Watt, SOT-23 Low Capacitance TVS for High Speed Line Protections |
| SL05T1 | 300 Watt, SOT-23 Low Capacitance TVS for High Speed Line Protections |
| SL05T3 | 300 Watt, SOT-23 Low Capacitance TVS for High Speed Line Protections |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SL2150LH2R | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Cable Tuner Front End LNA with AGC |
| SL2150LH2S | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Front End Power Splitter with AGC |
| SL2150LH2T | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Cable Tuner Front End LNA with AGC |
| SL215-3-1 | 制造商:SHUR-LOK 功能描述: |
| SL215A102KAB | 功能描述:多層陶瓷電容器MLCC - 含引線 50volts 1000pF 10% C0G RoHS:否 制造商:AVX 電容:470 pF 容差:10 % 電壓額定值:3 kV 端接類型:Radial 工作溫度范圍: 溫度系數/代碼:X7R 引線間隔:5.08 mm 產品:Automotive MLCCs 引線類型: |
發布緊急采購，3分鐘左右您將得到回復。