- 您現在的位置：買賣IC網 > PDF目錄368621 > SI9160 (Vishay Intertechnology,Inc.) Controller for RF Power Amplifier Boost Converter PDF資料下載
參數資料
| 型號： | SI9160 |
| 廠商： | Vishay Intertechnology,Inc. |
| 英文描述： | Controller for RF Power Amplifier Boost Converter |
| 中文描述： | 射頻功率放大器控制器升壓轉換器 |
| 文件頁數： | 6/11頁 |
| 文件大?。?/td> | 119K |
| 代理商： | SI9160 |
13
V
DD
N/C
V
S
D
R
D
S
P
GND
UVLO
SET
C
OSC
R
OSC
ENABLE
D
MAX
COMP
FB
NI
V
REF
GND
TSSOP-16
14
15
16
2
3
4
1
10
9
11
12
5
6
7
8
Top View
Order Number: Si9160BQ-T1
PIN DESCRIPTION
Si9160
Vishay Siliconix
www.vishay.com
6
Document Number: 70029
S-40700—Rev. H, 19-Apr-04
PIN CONFIGURATION AND ORDERING INFORMATION
ORDERING INFORMATION
Part Number
Temperature Range
Package
Si9160BQ-T1
25 to 85 C
TSSOP-16
Si9160BQ-T1—E3
Pin 1: V
DD
The positive power supply for all functional blocks except
output driver. A bypass capacitor of 0.1 F (minimum) is
recommended.
Pin 2: N/C
There is no internal connection to this pin.
Pin 3: D
MAX
Used to set the maximum duty cycle.
Pin 4: COMP
This pin is the output of the error amplifier. A compensation
network is connected from this pin to the FB pin to stabilize the
system. This pin drives one input of the internal pulse width
modulation comparator.
Pin 5: FB
The inverting input of the error amplifier. An external resistor
divider is connected to this pin to set the regulated output
voltage. The compensation network is also connected to this
pin.
Pin 6: NI
The non-inverting input of the error amplifier. In normal
operation it is externally connected to V
REF
or an external
reference.
Pin 7: V
REF
This pin supplies a 1.5-V reference.
Pin 8: GND (Ground)
Pin 9: ENABLE
A logic high on this pin allows normal operation. A logic low
places the chip in the standby mode. In standby mode, normal
operation is disabled, supply current is reduced, the oscillator
stops, and D
S
goes low while D
R
goes high.
Pin 10: R
OSC
A resistor connected from this pin to ground sets the
oscillator’s capacitor (C
OSC
) charge and discharge current.
See the oscillator section of the description of operation.
Pin 11: C
OSC
An external capacitor is connected to this pin to set the
oscillator frequency.
f
OSC
0.70
R
OSC
C
OSC
(at V
DD
= 5.0 V)
Pin 12: UVLO
SET
This pin will place the chip in the standby mode if the UVLO
SET
voltage drops below 1.2 V. Once the UVLO
SET
voltage
exceeds 1.2 V, the chip operates normally. There is a built-in
hysteresis of 200 mV.
Pin 13: P
GND
The negative return for the V
S
supply.
Pin 14: D
S
This CMOS push-pull output pin drives the external n-channel
MOSFET. This pin will be low in the standby mode. A
break-before-make function between D
S
and D
R
is built-in.
Pin 15: D
R
This CMOS push-pull output pin drives the external p-channel
MOSFET. This pin will be high in the standby mode. A
break-before-make function between the D
S
and D
R
is built-in.
Pin 16: V
S
The positive terminal of the power supply which powers the
CMOS output drivers. A bypass capacitor is required.
相關PDF資料 |
PDF描述 |
|---|---|
| Si9160BQ-T1 | Controller for RF Power Amplifier Boost Converter |
| Si9160BQ-T1-E3 | Controller for RF power amplifier boost |
| SI9165 | High Frequency 600-mA Synchronous Buck/Boost Converter |
| SI9166 | High Frequency Programmable Topology Controller |
| SI9167 | High-Frequency, High-Efficiency Buck Converter Design For Multi-Cell Battery Configured Systems Using Si9167 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI9160BQ-T1 | 功能描述:直流/直流開關轉換器 2MHz Controller RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| SI9160BQ-T1-E3 | 功能描述:DC/DC 開關控制器 Boost Conv For RF Pwr Amp RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| SI9160DB | 功能描述:電源管理IC開發工具 SI9160 Demo Board RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| SI9161 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Optimized-Efficiency Controller for RF Power Amplifier Boost Converter |
| SI9161BQ-T1 | 功能描述:DC/DC 開關控制器 Opt-Efficiency Cont RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發布緊急采購，3分鐘左右您將得到回復。