- 您現在的位置：買賣IC網 > PDF目錄365555 > Si786DSG (Vishay Intertechnology,Inc.) Dual-Output Power-Supply Controller PDF資料下載
參數資料
| 型號： | Si786DSG |
| 廠商： | Vishay Intertechnology,Inc. |
| 英文描述： | Dual-Output Power-Supply Controller |
| 中文描述： | 雙輸出電源控制器 |
| 文件頁數： | 12/14頁 |
| 文件大?。?/td> | 130K |
| 代理商： | SI786DSG |
Si786
Vishay Siliconix
www.vishay.com
12
Document Number: 70189
S-40807—Rev. J, 26-Apr-04
FIGURE 4.
Boost Supply for Gate Drivers
Level
Translator
DH_
BST_
LX_
DL_
V
L
PWM
V
L
V
L
BATTERY
INPUT
OPERATIONAL MODES
PWM Mode
The
continuous-current PWM mode when the load demands more
than approximately 25% of the maximum current (see typical
curves). The duty cycle can be approximated as Duty_Cycle
= V
OUT
/V
IN
.
3.3-V
and
5-V
Buck
controllers
operate in
In this mode, the inductor current is continuous; in the first half
of the cycle, the current slopes up when the high-side
MOSFET conducts and then, in the second half, slopes back
down when the inductor is providing energy to the output
capacitor and load. As current enters the inductor in the first
half-cycle, it is also continuing through to the load; hence, the
load is receiving continuous current from the inductor. By using
this method, output ripple is minimized and smaller form-factor
inductors can be used. The output capacitor’s ESR has the
largest effect on output ripple. It is typically under 50 mV; the
worst case condition is under light load with higher input
battery voltage.
Pulse-Skipping Mode
When the load requires less than 25% of its maximum, the
Si786 enters a mode which drives the gate for one clock cycle
and skips the majority of the remaining cycles. Pulse-skipping
mode cuts down on the switching losses, the dominant power
consumer at low current levels.
In the region between pulse-skipping mode and PWM mode,
the controller may transition between the two modes,
delivering spurts of pulses. This may cause the current
waveform to look irregular, but will not overly affect the ripple
voltage. Even in this transitional mode efficiency will stay high.
Current Limit
The current through an external resistor, is constantly
monitored to protect against over-current. A low value resistor
is placed in series with the inductor. The voltage across it is
measured by connecting it between CS_ and FB_. If this
voltage is larger than 100 mV, the high-side MOSFET drive is
shut down. Eliminating over-currents protects the MOSFET,
the load and the power source. Typical values for the sense
resistors with a 3-A load will be 25 m .
相關PDF資料 |
PDF描述 |
|---|---|
| Si786DSG-T1 | Dual-Output Power-Supply Controller |
| Si786LG | Dual-Output Power-Supply Controller |
| Si786LG-T1 | Dual-Output Power-Supply Controller |
| Si786LRG | Dual-Output Power-Supply Controller |
| Si786LRG-T1 | Dual-Output Power-Supply Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI786DSG-E3 | 功能描述:開關變換器、穩壓器與控制器 Dual 3.6V Step-Down RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| SI786DSG-T1 | 功能描述:開關變換器、穩壓器與控制器 Dual 3.6V Step-Down RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| SI786DSG-T1-E3 | 功能描述:開關變換器、穩壓器與控制器 Dual 3.6V Step-Down RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| SI786LG | 功能描述:DC/DC 開關控制器 3.3V Power Sup Cont RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| SI786LG-E3 | 功能描述:DC/DC 開關控制器 3.3V Power Sup Cont RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發布緊急采購，3分鐘左右您將得到回復。