- 您現在的位置：買賣IC網 > PDF目錄25644 > SI5338N-AXXXXXGM (SILICON LABORATORIES) 700 MHz, PROC SPECIFIC CLOCK GENERATOR, QCC24 PDF資料下載
參數資料
| 型號： | SI5338N-AXXXXXGM |
| 廠商： | SILICON LABORATORIES |
| 元件分類： | 時鐘產生/分配 |
| 英文描述： | 700 MHz, PROC SPECIFIC CLOCK GENERATOR, QCC24 |
| 封裝： | 4 X 4 MM, ROHS COMPLIANT, MO-220VGGD-8, QFN-24 |
| 文件頁數： | 15/42頁 |
| 文件大?。?/td> | 380K |
| 代理商： | SI5338N-AXXXXXGM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
Si5338
22
Rev. 1.0
3.5.4. Modifying a MultiSynth Output Divider Ratio/
Frequency Configuration
The output MultiSynth dividers of a configured and
phase-locked Si5338 can be modified without relocking
the PLL (i.e. without following section 3.5.3). This
feature allows any of the four output frequencies to be
modified without disturbing the others.
In this case, only write the set of registers associated
with the output MultiSynth divider (See AN411). The
feedback MultiSynth must not be modified unless
following the procedure in Section 3.5.3.
To avoid intermediate frequencies, it is recommended
that the output be disabled before changing the divider
ratio (see Register 230).
Any output MultiSynth that is reconfigured will lose its
phase alignment with the other outputs. SOFT_RESET
can be used to resynchronize the outputs (see "3.9.
The Si5338 can produce a glitchless frequency change
by using the Frequency Increment/Decrement function
as
described
in
3.5.5. Writing a Custom Configuration to NVM
An alternative to ordering an Si5338 with a custom NVM
configuration is to use the field programming kit
(Si5338/56-PROG-EVB) to write directly to the NVM of
a “blank” Si5338. Since NVM is an OTP memory, it can
only be written once. The default configuration can be
reconfigured by writing to RAM through the I2C interface
3.6. Status Indicators
A logic-high interrupt pin (INTR) is available to indicate
a loss of signal (LOS) condition, a PLL loss of lock
(PLL_LOL) condition, or that the PLL is in process of
acquiring lock (SYS_CAL). PLL_LOL is held high when
the input frequency drifts beyond the PLL tracking
range. It is held low during all other times and during a
POR or soft_reset. SYS_CAL is held high during a POR
or SOFT reset so that no chattering occurs during the
locking process. As shown in Figure 10, a status
register at address 218 is available to help identify the
exact event that caused the interrupt pin to become
active. Register 247 is the sticky version of Register
218, and Register 6 is the interrupt mask for Register
218.
Figure 10. Status Register
Figure 11 shows a typical connection with the required
pull-up resistor to VDD.
3.6.1. Using the INTR Pin in Systems with I2C
The INTR output pin is not latched and thus it should not
be a polled input to an MCU but an edge-triggered
interrupt. An MCU can process an interrupt event by
reading the sticky register 247 to see what event
caused the interrupt. The same register can be cleared
by writing zeros to the bits that were set. Individual
interrupt bits can be masked by register 6[4:0].
3.6.2. Using the INTR Pin in Systems without I2C
The INTR pin also provides a useful function in systems
that require a pin-controlled fault indicator. Pre-setting
the interrupt mask register allows the INTR pin to
become an indicator for a specific event, such as LOS
and/or LOL. Therefore, the INTR pin can be used to
indicate a single fault event or even multiple events.
Figure 11. INTR Pin with Required Pull-Up
3.7. Output Enable
There are two methods of enabling and disabling the
output drivers: Pin control, and I2C control.
3.7.1. Enabling Outputs Using Pin Control
The Si5338K/L/M devices provide an Output Enable pin
(OEB) as shown in Figure 12. Pulling this pin high will
turn all outputs off. The state of the individual drivers
when turned off is controllable. If an individual output is
set to always on, then the OEB pin will not have an
effect on that driver. Drive state options and always on
are explained in “3.7.2. Enabling Outputs through the
218
System Calibration
(Lock Acquisition)
Sys
Cal
0
PLL_LOL
1
2
3
4
5
6
7
Loss Of Signal
Clock Input
Loss Of Signal
Feedback Input
Loss Of Lock
LOS_FDBK LOS_CLKIN
INTR
VDD
1k
Control
NVM
(OTP)
Control & Memory
RAM
相關PDF資料 |
PDF描述 |
|---|---|
| SL28540ALCT | OTHER CLOCK GENERATOR, QCC56 |
| SL5504 | 1 CHANNEL TRANSISTOR OUTPUT OPTOCOUPLER |
| SL5582.3S | 1 CHANNEL TRANSISTOR OUTPUT OPTOCOUPLER |
| SLA-360MTT32S | T-1 SINGLE COLOR LED, YELLOW GREEN, 3.1 mm |
| SLA-570LT3FXH | T-1 3/4 SINGLE COLOR LED, RED, 5 mm |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI5338N-B01504-GM | 制造商:Silicon Laboratories Inc 功能描述:CLOCK - Bulk |
| SI5338N-B01504-GMR | 制造商:Silicon Laboratories Inc 功能描述:CLOCK - Tape and Reel |
| SI5338N-B01552-GM | 制造商:Silicon Laboratories Inc 功能描述:CLOCK - Bulk |
| SI5338N-B01552-GMR | 制造商:Silicon Laboratories Inc 功能描述:CLOCK - Tape and Reel |
| SI5338N-B01598-GM | 制造商:Silicon Laboratories Inc 功能描述:CLOCK - Bulk |
發布緊急采購，3分鐘左右您將得到回復。