- 您現在的位置：買賣IC網 > PDF目錄9580 > SI5315B-C-GM (Silicon Laboratories Inc)IC CLOCK MULT 8KHZ-125MHZ 36QFN PDF資料下載
參數資料
| 型號： | SI5315B-C-GM |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 22/54頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CLOCK MULT 8KHZ-125MHZ 36QFN |
| 應用說明： | SI5315/17 Crystal Selection AppNote |
| 標準包裝： | 490 |
| 系列： | DSPLL® |
| 類型： | 時鐘/頻率倍增器，抖動衰減器，多路復用器 |
| PLL： | 無 |
| 主要目的： | 以太網，SONET/SDH/PDH，電信 |
| 輸入： | CML，CMOS，LVDS，LVPECL |
| 輸出： | CML，CMOS，LVDS，LVPECL |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 2:2 |
| 差分 - 輸入:輸出： | 是/是 |
| 頻率 - 最大： | 125MHz |
| 電源電壓： | 1.71 V ~ 3.63 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 36-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 36-QFN（6x6） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
Si5315
Rev. 1.0
29
5.2. PLL Self-Calibration
An internal self-calibration (ICAL) is performed before operation to optimize loop parameters and jitter
performance. While the self-calibration is being performed, the DSPLL is being internally controlled by the self-
calibration state machine. The LOL alarm will be active during ICAL. The self-calibration time tLOCKHW is given in
Any of the following events will trigger a self-calibration:
Power-on-reset (POR)
Release of the external reset pin RST (transition of RST from 0 to 1)
Change in FRQSEL, FRQTBL, BWSEL, or XTAL/CLOCK pins
Internal DSPLL registers out-of-range, indicating the need to relock the DSPLL
In any of the above cases, an internal self-calibration will be initiated if a valid input clock exists (no input alarm)
and is selected as the active clock at that time. The external crystal or reference clock must also be present for the
self-calibration to begin. If valid clocks are not present, the self-calibration state machine will wait until they appear,
at which time the calibration will start. An output clock will be active while waiting for a valid input clock. The output
clock frequency is based on the VCO range determine by FRQSEL and FRQTBL settings. This output clock will
vary by ±20%. If no output clock is desired prior to an ICAL, then the SFOUT pins should be kept at LM for
1.2 seconds until the output clock is stable.
After a successful self-calibration has been performed with a valid input clock, no subsequent self calibrations are
performed unless one of the above conditions are met. If the input clock is lost following self-calibration, the device
enters holdover mode. When the input clock returns, the device relocks to the input clock without performing a self-
calibration.
5.2.1. Input Clock Stability during Internal Self-Calibration
An exit from reset must occur when the selected CKINn clock is stable in frequency with a frequency value that is
within the device operating range. The other CKINs must also either be stable in frequency or squelched during a
reset.
5.2.2. Self-Calibration caused by Changes in Input Frequency
If the selected CKINn varies by 500 ppm or more in frequency since the last calibration, the device may initiate a
self-calibration.
5.2.3. Device Reset
Upon powerup, the device internally executes a power-on-reset (POR) which resets the internal device logic. The
pin RST can also be used to initiate a reset. The device stays in this state until a valid CKINn is present, when it
then performs a PLL Self-Calibration (See 5.2. "PLL Self-Calibration”).
5.2.4. Recommended Reset Guidelines
Follow the recommended RESET guidelines in Table 10 when reset should be applied to a device.
Table 10. Si5315 Pins and Reset
Pin #
Si5315 Pin Name
Must Reset after Changing
2FRQTBL
Yes
11
XTAL/CLOCK
Yes
22
BWSEL0
Yes
23
BWSEL1
Yes
24
FRQSEL0
Yes
25
FRQSEL1
Yes
26
FRQSEL2
Yes
27
FRQSEL3
Yes
相關PDF資料 |
PDF描述 |
|---|---|
| MCZ33897AEF | IC TXRX CAN SGL WIRE 14-SOIC |
| VE-26X-MX-F2 | CONVERTER MOD DC/DC 5.2V 75W |
| VI-B1K-MW-F2 | CONVERTER MOD DC/DC 40V 100W |
| VE-26W-MX-F1 | CONVERTER MOD DC/DC 5.5V 75W |
| MCZ33897BEFR2 | IC TXRX CAN SGL WIRE 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI5315B-C-GMR | 功能描述:時鐘發生器及支持產品 Pin-Ctrl SyncE Clk Xplier/Jitt Attn 2/2 RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| SI5315-C | 制造商:AUK 制造商全稱:AUK corp 功能描述:IRED |
| SI5315-C(B) | 制造商:AUK 制造商全稱:AUK corp 功能描述:IRED |
| SI5315-C_1 | 制造商:AUK 制造商全稱:AUK corp 功能描述:IRED |
| SI5315-CB | 制造商:AUK 制造商全稱:AUK corp 功能描述:IRED |
發布緊急采購，3分鐘左右您將得到回復。